Home >> Application >> By Standard >> ISO >> ISO 5000~9999 >> ISO 7206-13 Femoral Head Fixation Torque Measuring Test

ISO 7206-13 Femoral Head Fixation Torque Measuring Test

Share:

ISO 7206-13 Hip Prosthesis Torque Resistance Tester | UnitedTest

UnitedTest manufactures ISO 7206-13 testing machine for measuring torque resistance to loosening of head fixation interface of stemmed femoral components for partial and total hip joint prostheses. This orthopedic implant test equipment supports modular hip taper connection torque evaluation, helps implant manufacturers complete preclinical mechanical verification, quality inspection and product qualification of hip prostheses under controlled laboratory torque loading conditions.


ISO 7206-13 specifies a standardized laboratory method to measure the torque required to loosen the head fixation interface of stemmed femoral components, for hip prostheses where the femoral head is designed to remain rotationally fixed relative to the stem neck. It covers modular hip taper locking assemblies for total hip arthroplasty and partial hip replacement implants, focusing on anti-torque performance of the head-stem connection. This mechanical test verifies the reliability of taper junctions, prevents rotational loosening risks in clinical service, and serves for implant R&D, batch quality control, regulatory submission and preclinical performance assessment of orthopedic hip implants.


Test principle:

A static torque is applied to the head/cone assembly and increased until either the connection between head and cone fails, or a chosen maximum torque is reached without failure. In practice: the head is locked into a fixture and an increasing torque is applied to the cone unit (via a lever arm or directly), while load and angular displacement are recorded continuously. The output is a torque–angle / torque–time curve, from which the breakaway (loosening) torque resistance and the angle at termination are reported.

ISO 7206-13 Femoral Head Fixation Torque Measuring Test


The specific test methods

There is one core mechanical method, with three permitted ways to grip the head and two permitted loading‑control modes.

MethodKey requirements

Machined parallel flats 

(form‑locking "flat‑wrench" fixation)

Flatten the head in the equatorial region to produce two parallel plane surfaces. Perpendicular distance between flats = 30 %–70 % of the ball‑head mean diameter.

Remaining wall thickness at the flats ≥ 2.0 mm. Note for a 28 mm head: 19.0 mm ± 0.5 mm has been found suitable.

Adhesive bonding into a spherical calotte (metal fixture)

Calotte must cover ≥ 140° of the head's hemisphere. Epoxy resin glues are cited as suitable.

 The bond breakaway torque must exceed the expected head/cone breakaway torque. If the bond fails first, record it and test an additional sample.

Embedding in cast resin (embedding fixture)

Cast resins (e.g. Technovit® 4071, or equivalent) are cited.

Same rule: embedding/head coupling torque must exceed the expected assembly breakaway torque; premature interface failure must be recorded and an additional sample tested.


Test Specimen info: 

  • Minimum sample size: 5 test specimens per cone unit to which the head is to be mounted.

  • Each specimen = a head + a neck (cone) of the intended head fixation.

  • Specimens may be real implants or coupon components.


Test Equipment for ISO 7206-13 Femoral Head Fixation Torque Measuring Test

Testing machine

Must comply with ISO 7500‑1 (verification/calibration of the force‑measuring system of static uniaxial machines). Shall provide: 

• axial compressive force through the head/cone axis for assembly, accuracy 1 % of full‑scale reading; 

• axial force at a point on a lever arm mounted on the cone unit, or direct torque application to the cone without a lever arm, accuracy 1 % of full scale; 

• instrumentation registering applied loads and angular displacement to ± 0.5°.

Loading fixtures

Designed to withstand all expected test loads, and to ensure the line of action of the applied torque is collinear with the central axis of the head-cone assembly.

The ideal fixture design allows 5 degrees of freedom (only rotation around the head/cone axis is constrained) to eliminate unwanted bending or side loads that would bias test results.

Cone unit

Either the actual clinical stem neck (cone) component, or a replica with identical dimensions, material, manufacturing process and specifications.


Test parameters

Torque loading rate20 N·cm/s ± 4 N·cm/s
Alternative rotation rate (if torque control is not feasible)0.05 °/s ± 0.01 °/s
Upper torque limit (pass criterion)50 N·m
Upper angle limit (test termination)20°
Parallel flat surfaces (head preparation method 1)Distance between flats = 30%–70% of mean head diameter; minimum remaining wall thickness at flats = 2.0 mm (19.0 ± 0.5 mm is recommended for a 28 mm head)
Glue/embedding fixation (methods 2 & 3)Bond breakaway torque must exceed the expected breakaway torque of the head-cone interface; calotte/resin shall cover at least 140° of the head hemisphere

Test Termination Criteria

The test is stopped when any one of the following occurs:

  1. The torque curve peaks and then decreases (indicating interface breakaway / failure).

  2. A torque of 50 N·m is reached without failure (the fixation is considered sufficiently strong).

  3. A relative rotation angle of 20° is reached. If failure occurs at the glue/fixture interface rather than the head-cone taper, the test is invalid and an additional specimen shall be tested.


Test Procedures of ISO 7206-13 Femoral Head Fixation Torque Measuring Test

  1. Define specimens — ≥ 5 head/cone assemblies per cone unit; real implants or coupons; identify head, cone, materials, geometry.

  2. Assemble ball head to cone unit according to ISO 7206-10, using the machine's axial compressive capability.

  3. Prepare head fixation; verify bond/embedding torque exceeds expected assembly breakaway torque.

  4. Mount the assembly into the fixture; align head/cone axis, fixture axis and torque axis; set up the 5‑DOF kinematic condition (only axial rotation constrained).

  5. Apply increasing torque to the cone unit at 20 N·cm/s ± 4 N·cm/s, or 0.05°/s ± 0.01°/s if torque control is impossible; record torque/time or angle/time continuously.

  6. Stop at load‑peak‑and‑drop, 50 N·m, or 20°; note the reason.

  7. Dismantle and examine the specimen, especially male/female taper surfaces, for damage.

  8. Report torque resistance, displacement angle at termination, termination reason, and all identification/result items; add an extra sample if a fixation interface failed prematurely or the 20° was fixture‑borne.

  9. Evaluate against customer‑defined acceptance criteria (mean lower limit + per‑sample lower limit vs. clinically successful predicate), then discard all components — no clinical reuse.



Industrial‑Field Application

FieldUse
Orthopaedic implant manufacturers (THA / partial hip, modular femoral heads, stems/trunnions)Design verification of new taper geometries, head diameters, material pairings, surface finishes, coatings, and assembly tooling.
Process / manufacturing validationChecking effects of taper angle tolerance, clearance, roughness, cleaning, contamination, sterilisation, and seating force on locking strength — the Introduction explicitly notes that nominally identical taper fixations can vary significantly in torsional locking strength.
Regulatory submissions / conformityMechanical evidence for FDA 510(k)/PMA (FDA Recognized Consensus Standard 11‑396, complete recognition, incl. AMD1:2022), EU MDR/CE technical documentation via the ISO 7206 / EN ISO 21535 family, China NMPA via YY/T 0809.13‑2020, UK/BSI via BS ISO 7206‑13.
Contract test labs, CROs, notified bodies, regulatorsComparative junction‑integrity testing, predicate comparison, root‑cause analysis of taper‑junction failures, recalls, and litigation support.
Materials R&DScreening metal/ceramic head materials, ceramic‑on‑metal combinations, large‑diameter metal‑on‑metal heads, trunnion / taper surface engineering.
Not used forRoutine lot release, in‑vivo wear prediction, cyclic fatigue life, or fretting‑corrosion rate quantification — those require other standards.


Related Standard: 

ASTM F1800

Standard practice for cyclic fatigue testing of metal tibial tray components of total knee joint replacements

ISO 21535Specific requirements for hip‑joint replacement implants
ASTM F2083Specification for Knee Replacement Prosthesis, specifies reference load magnitude, specimen quantity and run‑out cycle counts for tibial tray testing.
ISO 7206-10

Determination of resistance to static load of modular femoral heads (used for the burst test)

ASTM F3210Fatigue testing for knee femoral components
ASTM F2777endurance test for polyethylene tibial inserts.
ASTM F2009axial disassembly (pull-off) force of taper connections of modular prostheses
ISO 7206-13torque/head-fixation (torsion) test of the head–stem taper 
YY/T 0809.13Surgical implant parts and total hip prostheses - Part 13: Determination of torsional torque resistance of head fixation of stemmed femoral components
ISO 11491impact resistance of ceramic femoral heads
ISO 7206-4 / ISO 7206-6

endurance of stemmed femoral components and of the neck region; ASTM F2580 for modular proximally fixed stems; 

ASTM F2068 is the US analogue of ISO 7206-4 

ASTM F1814Guide for evaluating modular hip and knee joint components
ASTM F3161FEA of metallic TKA femoral components under closing conditions; the companion simulation route, and a recommended way to pick the worst-case condyle/size.
ASTM F2345

Standard Test Methods for Determination of Cyclic Fatigue Strength of Ceramic Modular Femoral Heads

ASTM F1264Standard specification and test methods for intramedullary fixation devices


Keywords: ASTM F2345, ceramic modular femoral head fatigue tester, cyclic fatigue strength test, total hip arthroplasty implant test, THA femoral head testing machine, hip prosthesis fatigue test, orthopedic implant mechanical test, ceramic hip head taper cone test, medical implant fatigue testing equipment, modular hip joint test, bioceramic implant fatigue test, orthopedic device lab tester, hip implant R&D test machine, femoral stem taper connection test, medical device fatigue test rig

Related products and device

ISO 7206-13 Dual axis Torsion & Bend Testing machine for Femoral Head Fixation Torque Measuring Test

Electronic Dynamic Universal Testing Machine/ Cyclic Testing Equipment widely used at material and components, parts dynamic mechanical property test, include tension, compression, low cycling test, match with high-low temperature chamber can execute the temperature test.

ISO 7206-13,hip prosthesis torque resistance tester

Torsion tester is mainly used to execute torsion test for various kinds materials, manual loading, high accuracy torsion transducer to measure torque, photoelectric encoder to measure torsion angle, digital display test result. Easy to operate and with budgetary price, most suitable for research institute and colleague, factory laboratory etc. to check the torsion character of different materials.

femoral head fixation torque tester

Electronic Fatigue Testing Machine designed for long-term cyclic load testing of metals, composites, and structural components, offering precise electronic control, repeatable results, and compliance with industrial standards.

ISO 7206-13 orthopedic prosthesis mechanical tester

Spinal Implant Constructs nail screw static and fatigue testing machine used to check the fatigue failure of medical nail, Loads are typically applied in a constant-amplitude, load-controlled sinusoidal waveform that runs more than 5 million times.

ISO 7206-13 Femoral Head Hydraulic Servo fatigue dynamic testing machine

Hydraulic fatigue dynamic testing machine mainly used at a variety of material and components, parts for both dynamic and static mechanical property testing, include tension, compression, low cycling test, match with high-low temperature chamber can execute the temperature test.

Static bending universal testing machine

UnitedTest universal testing machine with various test fixture, like peel, flexure, puncture, tear, pneumatic grip, belt tension etc., can be used to almost all materials include but not limited to steel rod, rubber, steel wire, plastic, seat belt, textile, wood, panel etc., mechanical performance inspection.

4 points bending fixture

The four point bending flexural test provides values for the modulus of elasticity in bending, flexural stress ,flexural strain and the flexural stress-strain response of the material. This test is very similar to the three point bending flexural test.

3 points bending grip

3 points bending grip used to measure the flexural modulus or flexural strength of a plastic material, conform with stanard ASTM D790, ISO 178.

Related Standard

ISO 7206-10 Femoral Head Static Compression and Tensile test –

ISO 7206-10: Implants for surgery --Partial and total hip joint prostheses -- Part 10: Determination of resistance to static load of modular femoral heads. 


It specifies a method for determining the static load resistance of the connection between a modular femoral head and a tapered cone of a femoral stem (the "head/cone junction") in hip joint prostheses. Include static compression (fracture) and tensile (disassembly) tests to quantify the load capacity of modular femoral heads with conical taper (Morse taper) connections. 


ASTM F1717 Spinal Implant Constructs Test –

ASTM F1717 Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Modelis a fundamental standard for evaluating the static and fatigue mechanical performance of spinal implant assemblies. Unlike ISO 12189, which focuses on a single device(an interbody cage), ASTM F1717 tests the entire posterior spinal construct—typically rods, screws, and cross-connectors—stabilizing a segment where a vertebral body has been removed (a "vertebrectomy" or "corpectomy" model). It simulates worst-case spinal instability to assess the implant's ability to maintain alignment and support loads.

ASTM F382 Metallic Bone Plates fatigue bending test –

ASTM F382 Standard Specification and Test Method for Metallic Bone Plates

ASTM F382 unified terminology, geometric classification, material requirements, marking & packaging rules, and mechanical test protocols for metallic bone plates used in surgical skeletal internal‑fixation. It define two mandatory test methods:  Single‑Cycle Bend Test and Bending Fatigue Test. Both adopt four‑point bending configuration. It is of great significance for ensuring the safety and reliability of metallic bone plates, which are widely used to align and fix bone segments in orthopedic reconstructive surgeries. 

ASTM F1798 Spinal Implant Subassembly Static and Fatigue Testing System –

ASTM F1798 Standard Test Method for Evaluating the Static and Fatigue Properties of Interconnection Mechanisms and Subassemblies Used in Spinal Arthrodesis Implants.

ASTM F1798 provides standardized methods for mechanically testing the interconnections within spinal implant systems. It is for evaluating the uniaxial static/fatigue strength and loosening resistance of interconnection mechanisms in spinal arthrodesis implant subassemblies, providing a standardized way to characterize mechanical performance of connections like rod-clamp, screw-rod, and hook-rod assemblies. It is critical for design validation, regulatory compliance, and clinical safety in the spinal implant industry.

ASTM F2706 Fatigue Static Test of Spinal implant constructs –

ASTM F2706 is a critical biomechanical evaluation tool in the medical device industry, specifically for spinal implants. ASTM F2706 establishes standardized mechanical test methods to evaluate the static (strength) and fatigue (long-term durability) performance of spinal implant assemblies intended for use in the occipito-cervical (OC) and cervico-thoracic (CT) regions (from the skull to the upper back). It simulates a worst-case scenario: a complete vertebrectomy (removal of a vertebra), creating a highly unstable spine segment that the implant must stabilize.

ASTM F2706 establishes standardized mechanical test methods to evaluate the static (strength) and fatigue (long-term durability) performance test, defines in‑vitro mechanical test protocols for posterior occipital‑cervical (OC) and occipital‑cervical‑thoracic (OCT) spinal fixation assemblies under a vertebrectomy worst‑case model, aiming for relative mechanical comparison of implant designs, rather than defining pass‑fail performance thresholds. 


ASTM F1264 Intramedullary Fixation Device Torsion & Bend Fatigue Test –

ASTM F1264 Standard Specification and Test Methods for Intramedullary Fixation Devices

ASTM F1264 is a standard specification used to describe the design and mechanical function of intramedullary fixation devices (IMFDs). It establishes terminology, classification, material, marking‑labeling requirements and four mandatory‑annex mechanical test methods for intramedullary nails/rods used in skeletal fracture fixation. It does not define mandatory clinical performance thresholds; tests deliver comparative mechanical data rather than absolute clinical pass‑fail criteria.

it also includes four standard testing methods: 

1, static four point bending test method (Annex A1), 

2, static torsion test method (Annex A2), 

3, bending fatigue test method (Annex A3), 

4, bending fatigue test method for IMFD locking screws (Annex A4). 


The UTDS series Dynamic/Fatigue Testing machine used for bone needle,  bending intramedullary nail fatigue test is mainly used for biomechanical performance testing of various materials, including artificial blood vessels, soft tissues, bones, bone plates, and vertebrae Interfusion device, knee joint, spine Dynamic and static mechanical tests on materials such as column fixators, metal coatings, hip joints, and intramedullary nails, including tension, compression, bending, and torsion.

ISO 7206-4, ISO 7206-6: Fatigue testing of femoral stem and femoral neck of hip prostheses –

ISO 7206‑4 and ISO 7206‑6 are key international standards defining fatigue endurance tests for stemmed femoral components of partial and total hip joint prostheses. ISO 7206‑4 evaluates the femoral stem under simulated proximal loosening; ISO 7206‑6 evaluates the femoral neck under well‑fixed, normal in‑vivo loading. 

ISO 7206-8 Hip Joint Replacement Torsion Testing, endurance properties of stemmed femoral components –

ISO 7206-8: Implants for surgery -- Partial and total hip joint prostheses -- Part 8: Endurance performance of stemmed femoral components with application of torsion. 


ISO 7206-8 standard as a series of test methods capable of effectively evaluating the endurance performance of stemmed femoral components designed for total and partial hip joint prosthesis. The standard allows experts to subject test specimens to loading conditions that mirror those seen in real conditions when patients use their hip joint prosthesis. The standard’s objective is to determine if hip implants perform as expected, ensuring their functionality and safety will be reliable for the patients who depend on them.


ISO 7206-13 Femoral Head Fixation Torque Test : Frequently Asked Questions

Q1: What is ISO 7206-13?

A: ISO 7206-13:2016 is an international standard that specifies a standardized laboratory test method for determining the torsional resistance (torque-to-failure) of the head fixation interface on stemmed femoral components of total and partial hip joint prostheses. It measures how much torque is required to loosen or break the conical taper connection between the femoral head and the stem neck.


Q2: Why is the ISO 7206-13 test important?

A: The test is critical because torsional instability at the head-neck taper interface is a leading cause of hip implant failure. Relative micromotion between the head and stem causes fretting corrosion, wear debris generation, and adverse local tissue reactions (ALTR), often leading to painful revision surgery. ISO 7206-13 provides a quantitative, reproducible method to validate taper locking strength before clinical use.


Q3. Is this a material test or an assembly test?

Strictly, it is an interface / assembly test, not a bulk-material coupon test. But it is highly material-dependent: locking strength varies with bearing-material pairing, head diameter, clearance, taper angle/tolerances, surface finish and manufacturing process. The standard explicitly warns that nominally identical taper fixations can vary significantly in torsional strength.


Q4. Which products and materials are covered?

Femoral components of total or partial hip replacements where the head and the neck/stem (“cone”) are separate components, joined by a locking conical taper or any other means, with the head not intended to rotate. Both metallic and non-metallic materials are in scope — e.g. metal or ceramic heads on metal cones.


Q5: How many test specimens are required per design?

A: A minimum of 5 test specimens must be tested for each cone unit / head design combination. Each specimen consists of one femoral head paired with one corresponding neck/cone component.


Q6: What are the three approved head fixation methods for testing?

A: The standard specifies three valid methods for gripping the femoral head:

  1. Flat-wrench method: Two parallel flat surfaces machined on the head's equatorial region for form-locking engagement.

  2. Adhesive bonding method: The head is glued into a metallic spherical calotte fixture using high-strength epoxy.

  3. Resin embedding method: The head is cast into a potting resin (e.g., Technovit 4071) inside a fixture.

For methods 2 and 3, the bond strength must exceed the expected taper breakaway torque.


Q7: What is the standard loading rate for ISO 7206-13?

A: The torque shall be applied at a rate of 20 N·cm/s ± 4 N·cm/s. If torque control is not feasible, an alternative displacement rate of 0.05°/s ± 0.01°/s may be used. Torque and angular displacement must be continuously recorded throughout the test.


Q8: When is the test terminated?

A: The test stops when any one of three conditions is met:

  • The torque curve peaks and decreases (interface breakaway / failure).

  • A torque level of 50 N·m is reached without failure (considered sufficiently strong).

  • A relative rotation angle of 20° is reached.

If slippage occurs at the fixture-head interface (glue failure) rather than at the taper, the test is invalid and an additional specimen must be tested.


Q9: Who performs ISO 7206-13 testing?

A: Testing is typically conducted by:

  • Orthopedic implant manufacturers (R&D, quality control, regulatory submission).

  • Independent third-party testing laboratories specializing in medical device evaluation.

  • Regulatory bodies for conformity assessment and market approval.


Q10. ISO 7206-13 vs ASTM F2009 — what is the difference?

ISO 7206-13 = torsional / rotational loosening torque. ASTM F2009 = axial disassembly force (pull-off force) of self-locking taper connections for modular prostheses, primarily developed for metal and ceramic heads on metal tapers. They are complementary: one resists twist, the other resists pull-off. Run both when characterising a modular taper junction.


Q11. Can one UnitedTest frame cover ISO 7206-10 and ISO 7206-13?

Often yes in principle, because both need a calibrated static frame and axial compressive assembly force; ISO 7206-13 additionally needs controlled torque application, angle capture and the alignment fixture. Confirm with UnitedTest that HDST Series has the required torque range, fixture interfaces and software fields for both reports — do not assume interchangeability from the frame alone.


Q12. Why choose ISO 7206-13 Hip Prosthesis Torque Testing Machines from UnitedTest? 

UnitedTest designs and manufactures high-precision ISO 7206-13 compliant torque testing systems for the orthopedic implant industry. Our test machines deliver accurate, repeatable measurement of femoral head fixation torque resistance, enabling implant manufacturers, testing laboratories and research institutions to validate taper junction performance according to ISO 7206-13:2016 international standards.


Our ISO 7206-13 head fixation torque testers are engineered to evaluate the torsional locking strength of modular femoral head-stem taper connections. Whether testing metallic or ceramic femoral heads on conical tapers, UnitedTest systems apply controlled static torque at the standard-specified rate of 20 N·cm/s, with continuous acquisition of torque and angular displacement data throughout the test cycle.


Fully Compliant with ISO 7206-13 and ISO 7500-1

Every UnitedTest torque testing machine meets the accuracy requirements of ISO 7500-1 (1% full-scale force accuracy) and supports all three head fixation methods defined in ISO 7206-13: flat-wrench form-locking, adhesive calotte bonding, and resin embedding. Our precision-aligned fixturing ensures collinear torque application with 5 degrees of freedom, eliminating parasitic bending loads that could compromise test validity.


Key Features of UnitedTest ISO 7206-13 Test Systems

  • Dual-mode control: Torque rate control (20 N·cm/s ± 4 N·cm/s) and angle rate control (0.05°/s ± 0.01°/s).

  • High-resolution data acquisition: Simultaneous torque, angle and time recording with ±0.5° angular accuracy.

  • Integrated axial assembly: Built-in compressive loading for specimen preparation per ISO 7206-10.

  • Configurable termination criteria: Auto-stop at breakaway detection, 50 N·m torque limit, or 20° angle limit.

  • Comprehensive reporting software: Generates test reports with all parameters required by ISO 7206-13 clause 6.6.

  • Versatile fixturing: Compatible with 22 mm to 40+ mm femoral heads and all standard taper geometries (12/14, 14/16, etc.).


Trusted by Orthopedic Implant Manufacturers Worldwide

UnitedTest serves orthopedic device manufacturers, medical testing laboratories, and biomechanics research centers across the globe. Our ISO 7206-13 torque test equipment supports R&D validation, production quality control, and regulatory submission for total hip replacement and partial hip prosthesis systems.


Complete ISO 7206 Series Testing Solutions

Beyond head fixation torque testing, UnitedTest offers a full range of orthopedic implant test equipment covering the entire ISO 7206 series, including ISO 7206-4 femoral stem endurance testing, ISO 7206-6 neck region fatigue testing, ISO 7206-10 static load testing for modular heads, and ISO 7206-12 acetabular shell deformation testing.

< Previous: ISO 7206-10 Femoral Head Static Compression and Tensile test

> Next: ISO 7231 Polymeric materials, cellular, flexible Determination of air flow value at constant pressure drop

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.