Information on the most widely used ASTM standards within the materials testing industry
ISO 8013 Vulcanized Rubber Creep Tester | Compression & Shear Creep Testing Machine - UnitedTest
UnitedTest supplies ISO 8013 rubber creep testing machines to measure compression creep and shear creep of vulcanized rubber under constant load and controlled temperature. Ideal for rubber material R&D, quality inspection and performance verification for sealing, damping and rubber component applications.
ISO 8013 specifies standardized laboratory test procedures to evaluate the creep performance of vulcanized rubber specimens subjected to sustained compression or shear loading within stable thermal conditions. It records time-dependent deformation data to assess long-term dimensional stability and load-bearing reliability of rubber materials. This standard excludes testing scenarios with intermittent deformation cycles, focusing exclusively on static continuous loading conditions. Our UnitedTest creep tester fully complies with ISO 8013 requirements, delivering stable, repeatable test results for rubber manufacturers, material laboratories and component suppliers.
Test Principle:
When vulcanized rubber is subjected to a constant stress at a constant temperature, its deformation does not remain stable but increases progressively over time — this time-dependent viscoelastic phenomenon is defined as creep. (The reverse effect — stress reduction under constant strain — is termed stress relaxation.)
Creep in rubber arises from two coexisting mechanisms:
Physical creep: Dominates at normal/low temperatures and short test durations, and generally follows a logarithmic relationship with time.
Chemical creep: Dominates at high temperatures and long test durations, driven by material degradation, and generally follows a linear relationship with time.
The core principle of the test is to apply a precisely controlled constant compressive or shear load to a standardized rubber specimen under stable temperature, then measure the progressive change in deformation at defined time intervals to quantify the material’s time-dependent mechanical response.
Specific Test Methods
1, Compression Creep Test: Measures the progressive increase in compressive strain over time under a constant axial compressive load. The specimen is compressed between two parallel rigid plates, and the reduction in specimen thickness is tracked at specified time points.
2, Shear Creep Test: Measures the progressive increase in shear strain over time under a constant shear load. A double-shear rubber-metal bonded specimen is used, and the lateral displacement of the central metal plate relative to the fixed outer plates is measured.
Test Specimen Information:
| Compression Test Specimens | Cylindrical discs, available in two standard sizes: Type A: (29.0 ± 0.5) mm diameter, (12.5 ± 0.5) mm thickness Type B: (13.0 ± 0.5) mm diameter, (6.3 ± 0.3) mm thickness (These correspond to Type A/B specimens defined in ISO 815-1.)
|
| Shear Test Specimens | Configuration: Double-shear assembly — rubber layers bonded between two outer rigid plates and one central rigid plate. Cross-section may be circular or square. Dimension rule: Diameter (or side length for square specimens) must be at least 4 times the rubber thickness to minimize bending, ensuring apparent shear modulus differs by less than 3% from the true value. Maximum rubber thickness: 13 mm (to ensure uniform vulcanization). Standard size: 25 mm diameter, 6.3 mm rubber thickness. Specimens defined in ISO 4664-1 or ISO 1827 may also be used.
|
ISO 8013 Rubber Creep Compression and Shear Test Required Testing Equipment:
| Creep Test Machine | Applies full load with negligible overshoot and maintains force constant within ±0.1%. Deformation measurement accuracy: ±0.1% of the initial specimen thickness. The line of action of the applied force remains coincident with the specimen axis as creep occurs. |
| Compression Test Device | Two parallel, flat, rigid steel plates with a surface finish no worse than 0.2 μm arithmetic mean deviation (for unbonded specimens; plate surfaces may be lubricated with silicone or fluorosilicone fluid). One plate is rigidly fixed; the other moves friction-free along the central axis of the specimen. |
| Shear Test Device | Designed for double-shear bonded specimens. Applies constant shear force with negligible overshoot, maintained within ±0.1%. Force acts in the plane of the central metal plate, through its center, perpendicular to the undeformed rubber layers. The central plate moves friction-free and only in the direction of the applied force. Displacement measurement accuracy: 0.01 mm. |
| Temperature-Controlled Chamber | Constructed in accordance with ISO 23529, with forced air circulation. Maintains test temperature within the specified tolerances. |
Key Test Parameters:
Initial Strain Target: The applied force is selected to produce an initial strain of (20 ± 2)% for both compression and shear. Guidance on force values for different rubber hardness levels is provided in Annex A (informative).
Force Application Speed: Full force must be reached within 6 seconds (0.1 min) with no significant overshoot.
Test Temperatures (recommended): Standard laboratory temperature, 55±1°C, 70±1°C, 85±1°C, 100±1°C, 125±2°C, 150±2°C, 175±2°C, 200±2°C, 225±2°C, 250±2°C. Sub-ambient and other temperatures are also permitted.
Measurement Time Points:
First measurement at (10 ± 0.2) minutes after full force application.
Subsequent measurements follow an approximately logarithmic timescale (e.g., 100 min, 1000 min, 10 000 min; or 1 day, 2 days, 4 days, 7 days, etc.).
Test procedure of ISO 8013 Rubber Creep Compression and Shear Test
Apparatus Thermal Stabilization: Bring the test device to the specified test temperature and allow all components to reach thermal equilibrium.
Specimen Temperature Conditioning: Hold the specimen at test temperature for a minimum of 30 minutes to achieve thermal equilibrium.
Initial Dimensional Measurement:
Compression: Measure initial thickness δ0 at test temperature.
Shear: Measure total sandwich thickness and calculate rubber thickness by subtracting the known thicknesses of the metal plates.
Determine initial cross-sectional area A0.
Specimen Mounting: Install the specimen in the test fixture; record the initial reading or set the displacement indicator to zero.
Load Application: Apply the full constant force within 6 seconds, with negligible overshoot.
Deformation Recording: Measure and record deformation at 10 minutes and at each subsequent specified time interval, maintaining constant force and temperature throughout the test.
Data Calculation: Compute creep increment, creep index, and compliance increment for each specimen.
Result Compilation: Determine the median value across all specimens; test additional specimens if the outlier criterion (>10% deviation from median) is triggered.
Industries Application:
| Industry | Examples | Why creep data is needed |
|---|---|---|
| Automotive / transport | Engine mounts, suspension bushings, rubber springs, exhaust hangers, body mounts, railway pads | Long-term sag changes ride height, alignment, NVH and preload |
| Civil / structural engineering | Elastomeric bridge bearings, seismic/base-isolation bearings, building mounts | Creep alters bearing height and load distribution over decades |
| Industrial machinery | Anti-vibration pads, machine mounts, coupling elements, conveyor/roller covers | Maintains positioning, clearance and isolation performance |
| Sealing | Gaskets, O-rings, static seals under constant compression | Time-dependent deformation contributes to loss of sealing force/geometry (often studied together with stress relaxation) |
| Energy / marine / aerospace | Wind-turbine elastomeric components, off-shore mounts, aircraft engine mounts | High-temperature capability up to 250 °C supports under-hood and hot-environment qualification |
| Rubber producers / compound R&D / QC labs | Compound development, filler/cure-system comparison, batch acceptance, specification compliance | Creep increment/index/compliance increment give comparable numbers for material ranking |
| CAE / design | FEA material cards, long-term modulus/compliance, service-life models | Provides time-dependent compliance rather than only instantaneous stiffness |
Related Test Standard
| ISO 178 | Plastics — Determination of flexural properties (the foundational standard for plastic bending testing, defining specimen geometry and bending fundamentals) |
| ASTM D695 | Test Method for Compressive Properties of Rigid Plastics (compressive specimen basis) |
| ISO 815-1 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures. It measures permanent residual deformation after compression and release, while ISO 8013 measures time-dependent deformation under sustained load; both are widely used to evaluate long-term mechanical stability of rubber. |
| GB/T 19242 | Rubber, vulcanized — Determination of creep in compression or shear — Chinese national standard |
| ASTM D6112 | compressive/flexural creep of plastic lumber and shapes |
| ISO 1827 | Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods |
| ISO 8013 | Rubber, vulcanized — Determination of creep in compression or shear |
| ISO 899-1 | Tensile creep and creep-rupture |
| ISO 899-2 | Flexural creep Test |
| ISO 4664-1 | Rubber, vulcanized or thermoplastic — Determination of dynamic properties — Part 1: General guidance |
| ASTM D2990 | Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
Keywords: ISO 8013 rubber creep tester, vulcanized rubber compression creep test, rubber shear creep tester, rubber creep measurement, static creep test equipment, rubber material long term deformation test, rubber damping material testing, rubber seal creep performance, vulcanized rubber testing machine, constant load creep test, temperature controlled creep tester, rubber lab testing instrument, rubber quality control test, polymer creep analysis, rubber component durability test
Related products and device
Related Standard
ASTM D2990 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D2990 defines procedures to measure time-dependent deformation (creep) and time-to-failure (creep-rupture) of plastic materials under constant static load and controlled environmental conditions.
ISO 899-1 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 899-1 determines tensile creep of plastics in the form of standard test specimens under specified conditions of pretreatment, temperature and humidity. It applies to rigid and semi-rigid, non-reinforced, filled and fibre-reinforced plastics, using dumb-bell-shaped specimens that are either directly moulded or machined from sheets or moulded articles.
ISO 527-1 covers the test procedures for determining tensile properties of plastics and plastic composites. Tensile properties of plastics that are determined through the practices of ISO 527-1 include tensile strength, tensile modulus and other properties related to stress strain characteristics of plastic materials.
ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1. The methods described in ISO 527-2 are selectively suitable for use with the following range of materials: rigid and semi-rigid thermoplastics moulding, extrusion and cast materials, including compounds filled and reinforced by, for example, short fibres, small rods, plates or granules but excluding textile fibres (see ISO 527-4 and ISO 527-5).
ASTM D638 determining the tensile properties of unreinforced and reinforced plastics using dumbbell-shaped (dogbone) specimens tested under closely controlled conditions of conditioning, temperature, humidity, and crosshead speed. For measuring the tensile mechanical properties of unreinforced and reinforced plastics, including thermoplastics, thermosets, molded plastics, and plastic composites.
ASTM D695: Standard Test Method for Compressive Properties of Rigid Plastics
ASTM D695 test covers the determination of the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading. Test specimens of standard shape are employed. This procedure is applicable for a composite modulus up to and including 41,370 MPa (6,000,000 psi). It is technically equivalent to ISO 604 Plastics‑Determination of Compressive Properties. This test applies end‑loading compression on standard‑geometry specimens under controlled environmental and displacement‑rate conditions, delivering compressive strength, yield strength, offset yield strength, compressive elastic modulus, and compressive deformation data.
ASTM D790: Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D790 determines flexural (bending) properties for unreinforced plastics, reinforced plastics, high‑modulus composites and electrical insulating materials via three‑point bending on simply‑supported rectangular beam specimens. It applies to rigid and semi‑rigid materials. Flexural strength cannot be calculated if the specimen neither yields nor fractures on its outer surface before reaching 5 % maximum outer‑fiber strain.
ASTM D2412: Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D2412 test method covers the determination of load-deflection characteristics of plastic pipe under parallel-plate loading. It covers thermoplastic resin pipe, reinforced thermosetting resin pipe (RTRP), and reinforced polymer mortar pipe (RPMP). Pipes tested under ASTM D2412 must be smaller than the envelope of the two compression platens by at least a half an inch. Square or circular platens can be used, with most customers choosing a square platen. Care must be taken to account for the mid-section of the pipe which will expand slightly as the pipe is compressed.
The characteristics determined by ASTM D2412 test method are pipe stiffness, stiffness factor, and load at specific deflections.
ASTM D3410 Shear Loading compression Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section.
ASTM D3410 measuring in‑plane compressive properties for high‑modulus‑fiber‑reinforced polymer‑matrix composites using pure shear‑loading via wedge grips, with an unsupported gage section on the test coupon. Test method determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers. It is applicable to composites made from unidirectional tape, wet-tow placement, textile (for example, fabric), short fibers, or similar product forms. Some product forms may require deviations from the test method.
ISO 899-2 Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading
ISO 899-2 specifies how to measure the time-dependent bending deformation of a freely supported plastic beam under a constant mid-span load, under controlled pre-treatment, temperature and humidity. Apply for rigid and semi-rigid, non-reinforced, filled and fibre-reinforced plastics; specimens moulded directly or machined from sheets or moulded articles.
Frequently Asked Questions (FAQs) – ISO 8013 Vulcanized Rubber Creep Test
Q1. What is ISO 8013:2019?
A: ISO 8013:2019, Rubber, vulcanized — Determination of creep in compression or shear, is the international laboratory method for measuring creep in vulcanized rubber that is continuously subjected to a compressive or shear force. It applies only to continuous loading; the standard explicitly cannot be used for intermittent deformation of rubber.
Q2. Why is the ISO 8013 creep test important?
A: Rubber is viscoelastic: under a load that never goes away, its deformation keeps growing. That gradual creep can change the height of a bearing, reduce preload in a mount, alter alignment, affect NVH performance, redistribute load or contribute to sealing problems. Hardness, tensile strength and short compression-set tests do not capture this time-dependent behaviour. ISO 8013 gives comparable numbers — creep increment, creep index and compliance increment — for material selection, QC, product validation, FEA input and service-life studies.
Q3. What is the difference between creep and stress relaxation?
A: They are mirror conditions:
Condition | What changes | Typical standard |
|---|---|---|
Constant force / stress | Strain increases with time → creep | ISO 8013 |
Constant strain | Stress/force decreases with time → stress relaxation | ISO 3384-1, ISO 6914, ASTM D6147 |
ISO 8013 measures the increase in deformation while the load is held constant.
Q4. Is ISO 8013 the same as a compression set test?
A: No. Compression set standards — ISO 815-1, ASTM D395, DIN 53517 — hold a specimen at constant strain, release it, and measure the unrecovered permanent deformation. ISO 8013 holds a constant force and measures deformation growth during loading, before any release. They answer different engineering questions.
Q5. Which materials and loading modes are covered?
A: The scope is vulcanized rubber under continuous compression or continuous shear. It is not a cyclic, fatigue, intermittent-deformation or thermoplastic-elastomer method. Related standards such as ISO 3384-1 and ASTM D6147 cover vulcanized or thermoplastic rubbers/elastomers for stress relaxation.
Q6. How long does an ISO 8013 creep test take?
A: There is no single fixed duration. The standard requires a reference reading at 10 ± 0.2 min and recommends additional readings on a logarithmic schedule such as 100 min, 1 000 min, 10 000 min or 1, 2, 4, 7 days and longer. The chosen duration and all reading times must be reported.
Q7: What is the difference between ISO 8013 creep test and ISO 815 compression set test?
A: ISO 8013 measures progressive, time-dependent deformation while the rubber remains under continuous constant load (creep under sustained stress). ISO 815 measures permanent residual deformation after the compressive load is removed and the rubber recovers (compression set). The two tests evaluate distinct viscoelastic properties and are commonly used together to assess long-term rubber performance.
Q8: What industries rely on ISO 8013 testing?
A: The test is critical for industries where rubber components operate under constant static load: automotive (engine mounts, suspension bushings, vibration isolators), civil engineering (bridge bearings, seismic isolators), aerospace (damping elements, static seals), industrial machinery (shock absorbers, anti-vibration mountings), and railway (rail pads, suspension components).
Q9: Can ISO 8013 be used for intermittent or cyclic loading?
A: No. ISO 8013 is designed exclusively for rubber under continuous compressive or shear force. It does not apply to intermittent deformation, cyclic loading or dynamic fatigue conditions.
Q10: Why choose ISO 8013 Creep Test Machine, Rubber Compression & Shear Creep Tester from UnitedTest?
A: UnitedTest manufactures ISO 8013 compliant rubber creep testing machines for vulcanized rubber compression and shear creep tests. Precision constant force control, wide temperature range and accurate deformation measurement for automotive, aerospace and engineering rubber components.
UnitedTest is a professional manufacturer of high-precision rubber testing equipment, delivering fully compliant ISO 8013 creep test machines engineered for determining compression and shear creep properties of vulcanized rubber materials and finished components.
Our ISO 8013 rubber compression creep testers and shear creep test systems achieve stable constant force control within ±0.1% accuracy, with negligible overshoot during load application – strictly meeting the loading requirements defined in ISO 8013:2019. Equipped with high-resolution deformation measurement modules, temperature-controlled chambers covering ambient to 250°C (with sub-zero options available), and application-specific compression / double-shear specimen fixtures, the systems enable accurate, automated testing of creep increment, creep index and compliance increment for a wide range of rubber compounds.
Ideal for R&D laboratories, quality control departments and third-party testing institutions, UnitedTest vulcanized rubber shear creep test equipment supports standard Type A / Type B compression specimens and double-shear bonded specimens as specified in ISO 8013, ISO 1827 and ISO 4664-1. The systems are widely deployed across the automotive, civil engineering, aerospace, industrial machinery and railway industries to evaluate long-term creep resistance, optimize rubber formulations, validate component design life, and verify product reliability under sustained static load.
All UnitedTest ISO 8013 compliant creep testing systems are calibrated in accordance with ISO 18899 and the normative calibration schedule in ISO 8013 Annex B, delivering traceable, reproducible test results recognized by global quality frameworks. We also provide customized configurations, professional test software with automatic data acquisition and calculation, and full after-sales support to match diverse laboratory and production testing requirements.
Require More Customized Solutions?