Home >> Application >> By Standard >> ISO >> ISO 1 ~ 4999 >> ISO 899-1 Tensile Creep Testing for Plastics

ISO 899-1 Tensile Creep Testing for Plastics

Share:

ISO 899-1 Tensile Creep Tester for Plastics | UnitedTest

UnitedTest manufactures ISO 899-1 tensile creep testing machines to evaluate plastic creep behaviour under controlled temperature and humidity. Suitable for rigid, semi-rigid, filled and fibre-reinforced plastics with dumbbell specimens for long-term creep measurement and material engineering data.


ISO 899-1 Plastics — Determination of creep behaviour — Part 1: Tensile creep

ISO 899-1 defines a reliable laboratory test method to determine tensile creep performance of plastic specimens under defined pretreatment, temperature and humidity conditions. This standard applies to rigid and semi-rigid plastics, including non-reinforced, filled and fibre-reinforced plastic grades. Tests use dumbbell-shaped samples that can be directly moulded or machined from plastic sheets and finished moulded parts. Tensile creep data from ISO 899-1 testing helps engineers predict long-term deformation, select suitable polymers for structural applications, validate product designs, support R&D and quality control for plastic components exposed to sustained static load over time. UnitedTest supplies professional tensile creep test systems fully compliant with ISO 899-1 for polymer and plastic material laboratories.


Test Principle: 

Tensile creep is defined as the progressive increase in material strain over time under a constant applied tensile force, at fixed temperature and humidity. The test characterizes the time-dependent viscoelastic behavior of plastics by applying a constant initial stress and tracking strain evolution over an extended period.

Core defined metrics include:

  • Initial stress (σ): Tensile force per unit of initial cross-sectional area in the gauge section.

  • Tensile creep strain (εₜ): Relative elongation of the specimen gauge length at time t.

  • Tensile creep modulus (Eₜ): Ratio of initial stress to creep strain at a given time, representing the material’s time-dependent stiffness.

  • Nominal creep strain/modulus: Values calculated from grip separation distance instead of gauge length, intended for research and quality control use.

  • Time to rupture: Elapsed time under full load until specimen failure.

  • Creep strength limit: The initial stress that causes rupture or reaches a specified strain at a defined time and environmental condition.

  • Creep recovery: The reduction in strain after complete unloading, expressed as a percentage of the pre-unloading strain (optional measurement).


Specific Test Methods

Basic tensile creep test — constant load, continuous or scheduled extension measurement at controlled temperature/humidity; produces creep strain–time data and Et or E*t at each selected time.

ISO 899-1 Tensile Creep Testing for Plastics


Test Specimen Information:

Dumb-bell shaped specimens, with dimensions defaulting to the requirements of ISO 527-2 for tensile testing of moulding and extrusion plastics.

Rigid and semi-rigid plastics, including non-reinforced, filled, and fibre-reinforced polymer materials.


ISO 899-1 Tensile Creep Testing for Plastics Required Testing Equipment: 

Creep Test Machine

Applies load smoothly without transient overload, and maintains the test load within ±1% of the target value. 

For creep-to-rupture tests, it must prevent rupture shocks from being transmitted to adjacent loading stations. 

The mechanism must enable rapid, smooth, and repeatable loading.

Gripping device

Applies load smoothly without transient overload, and maintains the test load within ±1% of the target value. 

For creep-to-rupture tests, it must prevent rupture shocks from being transmitted to adjacent loading stations. 

The mechanism must enable rapid, smooth, and repeatable loading.

Extension-measuring device

May be contact-type (extensometers, electrical-resistance strain gauges) or contactless (optical systems operating on the cathetometer principle). 

Key requirements:

  • Measurement accuracy better than ±0.01 mm

  • No mechanical, thermal, or chemical influence on specimen deformation

  • Optical systems require the specimen longitudinal axis to be perpendicular to the optical axis

  • Strain gauges are only acceptable if they do not reinforce the specimen and adhesion remains stable for the full test duration.

Tools

Time-measurement device: Timekeeping accuracy of 0.1%.

Micrometer: Resolution of 0.01 mm or finer, for measuring specimen thickness and width.


Key Test Parameters:

  • Loading rate: Full test load must be applied smoothly within 1 to 5 seconds, with a consistent loading rate across all replicate tests of one material.

  • Preload: A small preload may be applied to eliminate equipment backlash, provided it does not affect test results. Preload is maintained for the full test duration.

  • Measurement schedule: Standard recommended time points for extension readings: 1 min, 3 min, 6 min, 12 min, 30 min; 1 h, 2 h, 5 h, 10 h, 20 h, 50 h, 100 h, 200 h, 500 h, 1000 h (and longer as needed). More frequent readings are required if discontinuities appear in the creep curve.

  • Time accuracy: Elapsed time is measured within ±0.1% or ±2 seconds, whichever tolerance is less strict.


Test procedure of ISO 899-1 Tensile Creep Testing for Plastics

  1. Specimen conditioning: Condition specimens per the relevant material standard, or per ISO 291 if no material-specific protocol exists. Testing is conducted in the same atmosphere used for conditioning, unless otherwise agreed by all interested parties.

  2. Dimension measurement: Measure the width and thickness of the conditioned specimen’s gauge section in accordance with ISO 527-1

  3. Specimen mounting: Mount the conditioned, measured specimen in the test grips, and set up the extension measurement system.

  4. Stress and load calculation: Select the target test stress, and calculate the corresponding applied force using the specimen’s initial cross-sectional area.

  5. Loading procedure

    • Apply preload (if used) only after the specimen has stabilized at test temperature and humidity. Measure the initial gauge length (L₀) or grip separation (L₀*) under preload.

    • Apply the full test load smoothly within 1–5 seconds. Define t = 0 at the moment full load is reached.

  6. Data collection: Record specimen extension at the scheduled time points throughout the test duration.

  7. Environmental monitoring: Record temperature and humidity at the start of the test, at least three times per day initially, and at least once per day once conditions are confirmed stable.


Industries Application:

The standard itself names three uses: engineering design, research & development, and research/quality control. ASTM's counterpart adds the same logic explicitly: such data serve to compare materials, design fabricated parts, characterise long-term performance under constant load and, in some cases, specification purposes .

Typical sectors and parts where ISO 899-1-type data are used include:

  • Automotive — interior trim, brackets, clips, housings and under-bonnet parts under sustained load at elevated temperature; creep strain limits are often written into OEM material specifications .

  • Pipes and pressure systems — PE water/gas pipes, fittings, geothermal piping: long-term dimensional stability and slow-crack-growth/lifetime assessment; related dedicated methods exist for PE pipes (e.g. ISO 16770 FNCT) .

  • Appliances, electrical/electronics — housings, load-bearing mouldings, cable insulation and sheathing that must retain dimensions and insulation integrity under long-term tension .

  • Construction and geosynthetics — geogrids, geomembranes, profiles, panels and structural plastic components subject to permanent load .

  • Industrial containers / tanks — blow-moulded chemical tanks and fuel tanks resisting long-term hydrostatic bulging .

  • Material suppliers and test labs — grade development, compound/filler/fibre comparison, incoming QC, comparable single-/multipoint databanks (ISO 10350-1 / ISO 11403-1), and generating design allowables for FEA and lifetime prediction.


Related Test Standard

ASTM D638Test Method for Tensile Properties of Plastics (tensile specimen geometry)
ASTM D695Test Method for Compressive Properties of Rigid Plastics (compressive specimen basis)
ASTM D790Test Methods for Flexural Properties (three-point bending method)
ASTM D6112compressive/flexural creep of plastic lumber and shapes
GB/T 11546.1Plastic - Determination of creep behaviour - Part 1: Tensile creep
GB/T 11546.2Plastics—Determination of creep behaviour—Part 2:Flexural creep by three-point loading
ISO 899-1Tensile creep and creep-rupture
ISO 899-2Flexural creep Test
ASTM D1780Practice for conducting creep tests of metal‑to‑metal adhesives, typically dead‑weight/lever tensile‑shear creep, temperature/time based.
ASTM D2990Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics


The directly comparable international family — ASTM D2990 VS ISO 899


ASTM D2990ISO 899-1ISO 899-2
ModeTensile + compressive + flexural (3-pt & 4-pt) in one documentTensile creep (and creep to rupture)Flexural creep by three-point loading only
SpecimenD638 Type I/II; D695; D790 barISO 527-1A/1B dumb-bells, moulded or machined10 × 4 × 80 mm bar from the multipurpose specimen
Strain measurement

Direct on specimen preferred;

 grip separation permitted with correction factors; 

anvil displacement OK for compression

Extensometer on gauge length required for engineering-design data; 

grip separation only for research/QC

Die movement corrected for rig self-deformation, or optical/video
Compressive creepCoveredNoNo


Keywords: ISO 899-1, tensile creep tester, plastic creep test machine, polymer tensile creep, creep behaviour test, rigid plastic creep, semi-rigid plastic creep, fibre reinforced plastic creep test, filled plastics creep measurement, dumbbell specimen creep test, long term creep testing, plastic deformation test, creep strain test, polymer engineering test, plastic material quality control, creep test equipment, sustained load tensile test, thermoplastic creep tester, thermoset creep test, ISO 899-1 test apparatus, plastic lab testing machine, creep rupture test, polymer mechanical property test, humidity controlled creep test, temperature controlled creep tester

Related products and device

ISO 899-1 Plastic tensile creeping testing machine

High Temperature Creep and Relaxation Testing Machine is designed as low cost solutions for long-term creep and stress relaxation testing applications of metallic and alloy materials under high temperature in accordance with ASTM, BS, EN, ISO and other similar international testing standards.

semi-rigid plastic creep, fibre reinforced plastic creep test, filled plastics creep measurement

WDW Series Computer Control Electronic Universal Testing Machine made by UNITEDTEST range from 100N to 600KN load capacity with various models like single columns, table type, door frame type etc., is used to perform tension, compression, flexure/bending, shearing, peeling etc., test for metal and nonmetal specimens.

creep test equipment, sustained load tensile test, thermoplastic creep tester

Compression test fixture is used to investigate the compressive behaviour of the test specimens and for determining the compressive strength, compressive modulus and other aspects of the compressive stress/strain relationship under the conditions defined.

Related Standard

ASTM D2990 Plastic Creep & Creep-Rupture Test –

ASTM D2990 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics 

ASTM D2990 defines procedures to measure time-dependent deformation (creep) and time-to-failure (creep-rupture) of plastic materials under constant static load and controlled environmental conditions. 

ISO 527-1, ISO 527-2 Tensile Test of Plastics Composites & plastics –

ISO 527-1 covers the test procedures for determining tensile properties of plastics and plastic composites. Tensile properties of plastics that are determined through the practices of ISO 527-1 include tensile strength, tensile modulus and other properties related to stress strain characteristics of plastic materials. 

ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1. The methods described in ISO 527-2 are selectively suitable for use with the following range of materials: rigid and semi-rigid thermoplastics moulding, extrusion and cast materials, including compounds filled and reinforced by, for example, short fibres, small rods, plates or granules but excluding textile fibres (see ISO 527-4 and ISO 527-5).

ASTM D638 Tensile Testing for Plastics –

ASTM D638 determining the tensile properties of unreinforced and reinforced plastics using dumbbell-shaped (dogbone) specimens tested under closely controlled conditions of conditioning, temperature, humidity, and crosshead speed. For measuring the tensile mechanical properties of unreinforced and reinforced plastics, including thermoplastics, thermosets, molded plastics, and plastic composites.

ASTM D695 Plastic & composites Compressive Testing –

ASTM D695: Standard Test Method for Compressive Properties of Rigid Plastics

ASTM D695 test covers the determination of the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading. Test specimens of standard shape are employed. This procedure is applicable for a composite modulus up to and including 41,370 MPa (6,000,000 psi). It is technically equivalent to ISO 604 Plastics‑Determination of Compressive Properties. This test applies end‑loading compression on standard‑geometry specimens under controlled environmental and displacement‑rate conditions, delivering compressive strength, yield strength, offset yield strength, compressive elastic modulus, and compressive deformation data.


ASTM D790 Bending Test Flexural Properties of Unreinforced and Reinforced Plastics –

ASTM D790: Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

ASTM D790 determines flexural (bending) properties for unreinforced plastics, reinforced plastics, high‑modulus composites and electrical insulating materials via three‑point bending on simply‑supported rectangular beam specimens. It applies to rigid and semi‑rigid materials. Flexural strength cannot be calculated if the specimen neither yields nor fractures on its outer surface before reaching 5 % maximum outer‑fiber strain.

ASTM D2412 Plastic Pipe Deflection Testing by Compression Loading Test –

ASTM D2412: Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

ASTM D2412 test method covers the determination of load-deflection characteristics of plastic pipe under parallel-plate loading. It covers thermoplastic resin pipe, reinforced thermosetting resin pipe (RTRP), and reinforced polymer mortar pipe (RPMP). Pipes tested under ASTM D2412 must be smaller than the envelope of the two compression platens by at least a half an inch. Square or circular platens can be used, with most customers choosing a square platen. Care must be taken to account for the mid-section of the pipe which will expand slightly as the pipe is compressed.

The characteristics determined by ASTM D2412 test method are pipe stiffness, stiffness factor, and load at specific deflections.

ASTM D3410 Shear Loading compression Test for Polymer Matrix Composite Materials with Unsupported Gage Section –

ASTM D3410 Shear Loading compression Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section. 

ASTM D3410 measuring in‑plane compressive properties for high‑modulus‑fiber‑reinforced polymer‑matrix composites using pure shear‑loading via wedge grips, with an unsupported gage section on the test coupon. Test method determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers. It is applicable to composites made from unidirectional tape, wet-tow placement, textile (for example, fabric), short fibers, or similar product forms. Some product forms may require deviations from the test method.

ISO 899-2 Plastic three-point flexural creep test –

ISO 899-2 Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading

ISO 899-2 specifies how to measure the time-dependent bending deformation of a freely supported plastic beam under a constant mid-span load, under controlled pre-treatment, temperature and humidity. Apply for rigid and semi-rigid, non-reinforced, filled and fibre-reinforced plastics; specimens moulded directly or machined from sheets or moulded articles.

Frequently Asked Questions (FAQs) About ISO 899-1 Tensile Creep Testing

Q1. What exactly does ISO 899-1 test?

It determines the tensile creep of plastics: the increase in strain over time while a dumb-bell specimen is held under a constant tensile force in a specified pretreatment, temperature and humidity. The result is a strain–time record from which creep strain, creep modulus, isochronous curves, rupture strength and recovery are derived.


Q2. Why is the ISO 899-1 tensile creep test important for plastics?

Plastics are viscoelastic materials, meaning their deformation depends on both applied stress and elapsed time — standard short-term tensile tests cannot predict long-term performance under sustained load. ISO 899-1 testing provides standardized, comparable data to evaluate dimensional stability, prevent premature failure of load-bearing components, support engineering design, and enable objective comparison between material formulations, manufacturing batches, and suppliers.


Q3. What does the ISO 899-1 test measure?

The test measures the progressive increase in strain (deformation) of a plastic specimen over time under a constant applied tensile load and stable environmental conditions. It quantifies core properties including tensile creep strain, tensile creep modulus, time-to-rupture, creep strength limit, and (optionally) creep recovery rate.


Q4. What types of materials can be tested under ISO 899-1?

ISO 899-1 applies to rigid and semi-rigid plastics, including non-reinforced, mineral-filled, and fiber-reinforced polymer materials. It works for specimens that are directly moulded, or machined from flat sheets, extrusions, or finished moulded articles.


Q5. What is the difference between tensile creep modulus and nominal tensile creep modulus?

  • Tensile creep modulus (Eₜ) is calculated using strain measured directly on the specimen’s gauge length via a precision extensometer; this data is required for formal engineering design applications.

  • Nominal tensile creep modulus (Eₜ)* uses strain derived from the change in grip separation distance; it is intended for research screening and routine quality control where high absolute accuracy is less critical.


Q6. How long does an ISO 899-1 creep test take?

Test duration varies by application: routine quality control screening tests typically run 100–1000 hours, while engineering design and long-term performance validation tests often run 1000–10,000 hours or longer. The standard recommends a standardized measurement schedule starting at 1 minute and extending through 1000+ hours.


Q7. What is physical ageing, and why does it matter for ISO 899-1 testing?

Physical ageing is the gradual rearrangement of polymer molecules toward a denser equilibrium structure when the material is held below its glass transition temperature. This effect reduces creep rate over time and can cause significant result variation if not controlled. ISO 899-1 includes an informative annex on physical ageing effects, and requires strict control of specimen thermal history and conditioning for valid comparative results.


Q8. What is the difference between ISO 899-1 and ASTM D2990?

Both standards measure tensile creep of plastics, but:

  • ISO 899-1 is the ISO international standard, aligned with ISO 527 specimen specifications, with dedicated guidance on physical ageing effects.

  • ASTM D2990 is the US ASTM standard that covers tensile, compressive, and flexural creep in a single document. Test parameters, precision tolerances, and reporting formats differ slightly between the two standards.


Q9. Can I use grip displacement instead of an extensometer?

Yes — but only for research/QC data, not for engineering-design data (Clause 1). Say so in the report. For creep-to-rupture work, a contactless optical cathetometer is recommended, gauge marks made with inert thermally stable paint or metal clips, and automatic rupture-time indication is desirable


Q10. How fast must the load be applied?

Full load must be reached between 1 s and 5 s after load application begins, and the same loading rate must be used for every test in one material series. t = 0 is the moment the specimen is fully loaded.


Q11. Why choose UnitedTest equipment for ISO 899-1 tensile creep testing?

UnitedTest tensile creep test systems are purpose-built to fully comply with ISO 899-1:2017 requirements, with customizable load ranges, multiple extensometer options, precision environmental control, and automated data analysis software that generates all required standard result curves. We provide end-to-end support including traceable calibration, method validation, and operator training to help laboratories achieve reliable, repeatable test results for R&D, quality control, and compliance testing.


Built to align with all mandatory specifications of ISO 899-1, UnitedTest tensile creep testers feature ±1% constant load control accuracy, high-resolution extension measurement (≤0.01 mm precision), optional non-contact optical extensometry, programmable temperature and humidity control (±2°C stability), and fully automated data acquisition software. The system generates all standard output formats required by the standard: creep curves, isochronous stress-strain curves, creep-modulus time curves, and creep-to-rupture curves. Configurations are available for short-term material screening tests and multi-thousand-hour long-term creep endurance testing, with optional creep recovery measurement functionality.


As a trusted global plastic creep test machine supplier, UnitedTest provides full technical support including specimen configuration guidance, test method validation, and traceable calibration to help laboratories achieve reliable, ISO 899-1-compliant test results for material development, quality assurance, and structural engineering design.

< Previous: ISO 845 Cellular Plastics & Rubber Apparent Density Testing

> Next: ISO 899-2 Plastic three-point flexural creep test

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.