Home >> Application >> By Standard >> Others >> EN 13770 Test — Abrasion Resistance of Knitted Footwear Garments Explained

EN 13770 Test — Abrasion Resistance of Knitted Footwear Garments Explained

Share:

EN 13770 Textile Abrasion Resistance Tester for Knitted Footwear Garments | UnitedTest

UnitedTest supplies EN 13770 abrasion testing machines for knitted footwear garments including socks, ankle socks and heavy tights. This standard defines two independent test methods to evaluate textile abrasion performance, with separate reporting requirements.


EN 13770 Textiles‑Determination of the abrasion resistance of knitted footwear garments. EN 13770 defines two test methods for the abrasion resistance of knitted footwear garments — e.g. ankle socks, socks, heavy tights — applicable irrespective of size, composition and construction. The two methods are independent. The method must be chosen before starting the test and recorded in the test report, because results from the two methods cannot be compared with each other.


Two Specific EN 13770 Test Methods, Principles, Equipment, Specimen Information, Key Parameters and Test Stipulations

Method 1: Martindale Abrasion Machine Method

Test Principle

Circular hosiery specimens taken from high‑wear sock zones are stretched over a flattened rubber surface. 

Specimens undergo cyclic Lissajous‑pattern planar abrasion motion against standard reference abradant under defined pressure. 

Abrasion performance is quantified as cycle counts until test endpoint: either hole formation (thread rupture) or fabric thinning of one yarn component in plated constructions (e.g. nylon‑cotton plated knit).

Test Equipment

Martindale abrasion‑testing machine complying with EN ISO 12947‑1.

- Modified special specimen holder assembly: guide spindle, holder body, needle ring, holder nut, rubber sphere with 20 mm flat test surface

- Spring‑loaded tightening‑block spanner (to maintain rubber flatness during clamping)

- Standard Martindale abradant and woven wool felt substrate

- 2.5 kg pressing weight (120 ± 10 mm diameter) for mounting abradant material

Test Specimen
  • Specimen dimension: 38 mm diameter circular cut pieces, preferably produced with cutting die.

  • Minimum sampling: 2 specimens from heel area, 2 specimens from sole area. Additional specimens may be cut for statistical averaging.

  • Sampling shall minimise tensile stress to avoid permanent over‑stretching of knitted fabric.

  • Auxiliary abradant: minimum 140 mm dimension; wool felt substrate: 140 mm +0.5/‑0 mm.

Main Test Parameters
  • Abrasion motion: standard Lissajous movement from EN ISO 12947‑1

  • Applied pressure load: 12 kPa on each specimen

  • Abradant replacement: new abradant for each test run or after 50 000 rub cycles; replace felt when heavily contaminated.

  • Inspection intervals (informative Annex B): inspect without removing specimens from holder at preset cycle intervals:

    • ≤10 000 cycles: inspect every 1 000 cycles

    • 10 000‑15 000 cycles: inspect every 2 000 cycles

    • 15 000‑30 000 cycles: inspect every 5 000 cycles

    • 30 000 cycles: inspect every 10 000 cycles

  • Trim surface pills with curved‑blade scissors during inspection.

  • Endpoint definition: hole formation OR yarn‑layer thinning; record cycle number corresponding to each endpoint separately if both are assessed.

Test Procedure

1. Mount specimen into modified holder assembly: fix specimen via needle ring, fit rubber sphere, assemble holder body‑nut with spring‑loaded spanner to keep fabric flat and properly stretched.

2. Mount new abradant and wool felt onto Martindale tables, compress with 2.5 kg weight then secure clamping ring.

3. Install assembled specimen holders onto machine, apply 12 kPa load pieces.

4. Set counter, zero totalising counter, start machine.

5. Stop at pre‑set inspection intervals to check for abrasion endpoint, remove pills if present.

6. Record rub cycles reaching thinning or hole failure.

7. Complete test report including method reference, sample ID, sampling area, endpoint type, individual cycle values, range/mean (if needed), and any deviations from standard requirements.

Method 2: Abrasion on Leg Forms

Test Principle

Full knitted hosiery garments are fitted onto volumetric leg forms, stretched to replicate real‑wear tension status. 

A dedicated abrasion tester delivers reciprocating linear rubbing motion against target test zones. 

Abrasion resistance is measured as cycle counts until endpoint: hole breakthrough or single‑component yarn thinning, same endpoint definition as Method 1.

Test Equipment
  • Abrasion tester unit (Annex C): slipper assembly, horizontal rail, lateral positioning discs, roller bearings, counter modules, two parallel test heads for dual‑specimen simultaneous testing, motor speed 250 strokes per minute, adjustable stroke length.

Interchangeable curved abradant shoes (10 mm width matching leg‑form curvature). Optional additional load weights for slipper.

  • Dimension‑specified leg forms (Annex D): cork‑covered two‑cylinder structures, available in Mondopoint sizing series.

Leg forms can be mounted vertically (test sole, toe‑heel reinforcement) or horizontally (test heel‑back, leg section).

  • Elastic retaining collars for garment fixation.

  • Abradant paper: 734 silicon carbide P1000 (Annex E), or alternative abradant agreed by contracting parties.

  • Foam backing material (Annex F).

  • Soft cleaning brush for specimen surface between inspections.

Test Specimen
  • Normally test 2 pairs of knitted footwear garments.

  • Total of minimum 12 test specimen locations: 8 positions on sole area, 4 positions on heel area (3 different wear areas per garment).

Extra test locations (leg, heel‑leg seam, toe) can be added by mutual agreement.

  • Garment must be fitted onto leg‑form of matching size; multi‑size products may be evaluated on multiple leg‑form sizes. No folds or wrinkles are allowed after mounting sample on leg form.

Main Test Parameters
  • Motor stroke speed: 250 strokes/minute

  • Reciprocating stroke length adjusted to 10 mm

  • Default test runs without extra slipper load; additional load is permitted only by contractual agreement.

  • Abradant paper replacement: change every 500 test cycles.

  • Inspection frequency: pause every 100 or 500 cycles; brush specimen surface with soft brush before wear assessment.

  • Endpoint criteria are identical to Method 1: hole rupture or yarn‑layer thinning.

  • Secure elastic retaining collars to prevent sample shifting during reciprocating abrasion.

  • Leg‑form orientation selection: vertical for sole/toe‑heel reinforcement; horizontal for heel‑back and leg part testing.

Test Procedure
  1. Mount leg form in horizontal or vertical orientation as required for target test zone.

  2. Select matched‑curvature abradant shoe and attach to tester slipper. Cut P1000 silicon‑carbide abrasive paper plus foam backing; bond them (foam sits between shoe and abrasive paper) with double‑sided adhesive tape.

  3. Position slipper assembly onto target test area; set stroke length to 10 mm. Apply optional extra weight only per prior agreement.

  4. Pre‑set counter to 100 cycles, reset total counter and start tester.

  5. When machine halts, lift slipper, brush specimen surface, inspect for abrasion failure endpoint. Continue cyclic abrasion with inspection intervals of 100 or 500 cycles until endpoint occurs. Record failure cycle number. Replace abrasive paper every 500 cycles.


Industry Application Fields

  • Hosiery and sock manufacturers (in-line QC, batch release, supplier comparison) and private-label/brand buyers setting durability specifications.

  • Product development: evaluating fibre blends (cotton, wool, bamboo, recycled polyester), yarn counts, plated constructions (nylon/cotton, nylon/wool), toe/heel reinforcement, terry/loop density, and finishes.

  • Performance segments: sports, outdoor, workwear and safety footwear socks, military, medical/compression and diabetic hosiery, children's socks (high abrasion zones).

  • Retailer/e-tender specifications and third-party labs (SGS, Intertek, TÜV, SATRA-type labs) as sole-source or comparative durability evidence; claim substantiation ("longer lasting", "reinforced heel") and complaint/arbitration between supplier and buyer.

  • Durability/eco-design and circular-economy programmes, where extended service life is a measurable sustainability KPI.


Related Standard: 

ISO 12947-1Textiles - Determination of the abrasion resistance of fabrics by the Martindale method - Part 1: Martindale abrasion testing apparatus
ISO 12947-2Textiles - Determination of the abrasion resistance of fabrics by the Martindale method - Part 2: Determination of specimen breakdown
ISO 12947-3Textiles - Determination of the abrasion resistance of fabrics by the Martindale method - Part 3: Determination of mass loss
ISO 12945‑2pilling & fuzzing on the modified Martindale apparatus — same machine family, different end point
ISO 5470-1Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Part 1: Taber abrader
ISO 5470-2Rubber- or plastics-coated fabrics. Determination of abrasion resistance. Martindale abrader
ASTM D4966Standard Test Method for Abrasion Resistance of Textile Fabrics (Martindale Abrasion Tester Method).
ASTM D4970

Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Martindale Tester

GB/T 21196.1Textiles-Determination of the abrasion resistance of fabrics by the Martindale method-Part 1:Martindale abrasion testing apparatus
JIS L 1096, M&S P19other commonly referenced abrasion/pilling methods
GBT 4802.2

Textiles - Determination of fabric propensity to surface fuzzing and to pilling - Part 2: Modified Martindale method

EN 13770Textiles - Determination of the abrasion resistance of knitted footwear garments
EN 16094
Laminate floor coverings. Test method for the determination of micro-scratch resistance


Keywords: EN 13770 abrasion tester, knitted footwear garment abrasion test, sock abrasion resistance tester, ankle sock abrasion testing, heavy tights textile abrasion machine, textile abrasion test equipment, knitted fabric abrasion measurement, footwear textile durability test, UnitedTest textile abrasion tester, textile wear resistance test machine

Related products and device

EN 13770 Knitted Footwear Garments Martindale Abrasion Tester

Martindale Abrasion Tester simulates real-world wear and friction in a controlled, accelerated manner to predict a material's durability and appearance retention over time. suitable for testing the abrasion resistance and pilling tendency of knitted fabrics, woolen fabrics.

Elongation Testing Tensile Testing Machine

A single column tensile tester is a sophisticated material testing instrument designed for measuring mechanical properties of various materials under tension, compression, bending, shear, and other loading conditions. As the name suggests, it features a single vertical column supporting a moving crosshead that applies force to test specimens.

Tensile Testing Jig

Vice Tensile test fixture for plastics is based on the test standatd ASTM D638, determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, speed.

Related Standard

ISO 12947-1 Martindale Abrasion Test for textile fabrics –

ISO 12947-1 Textiles — Determination of the abrasion resistance of fabrics by the Martindale method — Part 1: Martindale abrasion testing apparatus

ISO 12947-1 defines mandatory construction, dimensional, performance and auxiliary‑material requirements for Martindale abrasion testers, which are used to carry out the practical test procedures laid down in ISO 12947‑2,‑3,‑4. It is the specification for the machine and the consumables — the "hardware norm". The actual abrasion procedures live in Parts 2, 3 and 4, and Part 1 is written to guarantee that a Martindale result obtained in one lab is physically comparable to one obtained in another. 


ISO 5470-1 Abrasion Test of Rubber or Plastics Coated Fabrics by Taber Abrader Method –

ISO 5470-1: Rubber- or plastics-coated fabrics -- Determination of abrasion resistance -- Part 1: Taber abrader.

ISO 5470-1 specifies a method for determining the abrasion resistance of rubber- or plastics-coated fabrics using the Taber abrader apparatus. This test simulates wear under controlled conditions to evaluate a material's durability.

ISO 12947-3 Mass-Loss Abrasion Test by Martindale Abrasion Tester –

ISO 12947-3 Textiles — Determination of the abrasion resistance of fabrics by the Martindale method — Part 3: Determination of mass loss

ISO 12947-3 applies to all textile fabrics including nonwovens, and is used to determine the mass loss of specimens after controlled abrasion. It is explicitly not intended for fabrics where the specifier states the end performance is a deliberately low abrasion wear life.


ISO 13937-2 Trouser Method Fabric Tear Force Testing –

ISO 13937-2 Textiles – Tear properties of fabrics – Part 2: Determination of tear force of trouser‑shaped test specimens (Single tear method).

ISO 13937-2 is method for determining the tear force required to propagate an already-started single tear, using a rectangular specimen slit into two "trouser legs". Mainly for woven fabrics; may also apply to fabrics made by other techniques (e.g. some nonwovens). Not applicable to knitted fabrics, woven elastic fabrics, highly anisotropic fabrics, or loose fabrics where the tear tends to transfer from one direction to another. Only CRE (constant-rate-of-extension) machines are permitted.


ASTM D5035 Breaking Force and Elongation testing of Textile Fabrics (Strip Method) –

ASTM D5035 : Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method)


ASTM D5035 is the standard test method for determining breaking force (tensile strength) and elongation at break of textile fabrics using the strip method. It defines two core procedures--raveled strip (for woven fabrics) and cut strip (for nonwovens, coated/felted fabrics)--and supports both dry and wet testing.

ISO 12945-2 Martindale Pilling Test for Fabric Pilling, Fuzzing & Matting –

ISO 12945-2 Textiles — Determination of fabric propensity to surface pilling, fuzzing or matting — Part 2: Modified Martindale method

ISO 12945-2 specifies a method for determining the resistance to pilling, fuzzing and matting of textile fabrics using a modified Martindale machine. It ranks fabrics in the same order of surface-change propensity as is likely to occur in end-use wear.


ASTM D4966 Martindale Abrasion Test for Fabric Abrasion Resistance –

ASTM D4966 Standard Test Method for Abrasion Resistance of Textile Fabrics (Martindale Abrasion Tester Method) 

ASTM D4966 determination of the abrasion resistance of textile fabrics using the Martindale abrasion tester; generally applicable to knit, woven and nonwoven fabrics — material thickness may limit suitability because of specimen-holder capacity. It applies to woven, knit and non‑woven textiles, though excessive fabric thickness may restrict testing due to specimen‑holder physical limits.

ASTM D4970 Martindale Pilling Test for Surface Changes of Textile Fabrics –

ASTM D4970 Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Martindale Tester.

ASTM D4970 is the Martindale (Lissajous‑motion) fabric‑on‑fabric pilling test used to predict how badly a fabric will pill, fuzz or otherwise change its surface appearance in wear, reported on an arbitrary 5‑to‑1 rating scale (5 = no pilling, 1 = very severe pilling). 


ISO 12947-2 Fabric Breakdown Abrasion Testing by Martindale Abrasion Tester –

ISO 12947-2 Textiles - Determination of the abrasion resistance of fabrics by the Martindale method - Part 2: Determination of specimen breakdown

ISO 12947-2 measuring how many abrasion cycles — or "rubs" — a fabric withstands before itreaches a defined end point. A circular specimen is mounted in a holder under a defined loadand rubbed against a standard woven wool abradant in a translational movement tracing a Lissajous figure, while the holder rotates freely about its own axis. The abrasion resistance isreported as the number of rubs at the last inspection interval before specimen breakdownoccurs.

Because the end point is defined inside the standard — two broken threads for woven fabrics,one for knitted fabrics, a fully worn-off area for pile and flocked fabrics, a hole of at least 2.5mm for nonwovens — results are objective and comparable between laboratories. That is whythe Martindale figure is the durability number most often written into upholstery and contracttextile specifications.


ISO 17704 Martindale Abrasion Test for Footwear — Uppers, Linings & Insocks –

ISO 17704 Footwear — Test methods for uppers, linings and insocks — Abrasion resistance

ISO 17704  is method for determining the resistance of uppers, linings and insocks — irrespective of material — to wet and dry abrasion, in order to assess suitability for the end use. Note the standard deliberately gives no pass/fail criteria; it produces a description and rating of damage at prescribed rub counts.


FAQs for EN 13770 Test (Knitted Footwear Abrasion Resistance)

Q1. What is EN 13770?

A European standard that specifies two laboratory test methods for measuring the abrasion (wear) resistance of knitted footwear garments — for example ankle socks, socks and heavy tights. The result is always expressed as the number of rubs (Method 1) or cycles (Method 2) needed to reach a defined endpoint.


Q2. Which products does it cover?

Any knitted footwear garment: ankle socks, crew socks, dress socks, sports socks, heavy tights, and knitted shoe-liners. The standard explicitly applies irrespective of size, fibre composition and knit structure, so it covers cotton, wool, bamboo, polyester, nylon, blends, plated constructions, terry/cushioned soles and reinforced toe/heel designs alike.


Q3. Why does the standard contain two methods instead of one?

Because a sock is not a flat fabric. It is elastic, tubular and worn stretched over a three-dimensional foot inside a shoe, flexing under load. The two methods reproduce that condition at different levels:

  • Method 1 (Martindale) — a flat-ish, stretched circular specimen on a modified holder; efficient and inexpensive, good for routine quality control.

  • Method 2 (leg forms) — the whole garment stretched on a volumetric leg form, "as in wear"; the more realistic, whole-product approach, preferred for R&D, claim substantiation and dispute arbitration.


Q4. Can I compare a Method 1 result with a Method 2 result?

No. The Introduction of EN 13770 states that the method must be chosen before the test starts and recorded in the report, because results of the different methods cannot be compared with each other. Never mix or convert rub counts and cycle counts.


Q5. What exactly is the "hole" endpoint?

A hole, which usually develops when one thread/loop breaks, causing an opening to appear. In knits you typically see hole formation rather than the "two broken threads" endpoint used for woven fabrics.


Q6. What exactly is the "thinning" endpoint?

When the garment is knitted with a filament yarn plated together with a spun staple yarn (e.g. nylon/cotton or nylon/wool), the spun component can wear away first, leaving a thin base of the filament yarn. That "thinned" area is a legitimate endpoint, even though no hole has appeared. This is unique to hosiery and is why EN 13770 defines two endpoints.


Q7. Which endpoint should I report?

Whichever your specification requires — hole, thinning, or both. If both are determined, the report must state clearly which rub/cycle count belongs to which endpoint.


Q8. Can I use a standard Martindale tester for EN 13770 Method 1?

Yes — the machine itself is the standard EN ISO 12947-1 Martindale. But you must add the modified sock abrasion holder assembly (needle ring + 20 mm rubber sphere + holder nut/body) and the spring-loaded tightening block spanner, and you must apply the 12 kPa loading piece. A standard flat abrasion head will not reproduce the stretched state the method requires.


Q9. What leg-form size should be used?

The garment must be tested on the leg form of the same size as the garment. For multi-size ("one size fits all") socks, testing may be repeated on several leg-form sizes. The size actually used must be reported.


Q10. Can the tester be set up in different positions?

Yes. With the leg form vertical you test the sole and the toe/heel reinforcement; with the leg form horizontal you test the back of the heel and the leg.


Q11. Do I have to remove pills during inspection?

Yes. In Method 1, pills must be removed with sharp, curved-blade scissors during inspection, because pills obscure the surface and distort the assessment.


Q12. What must be in the test report?

Method 1: reference to Method 1 of EN 13770; sample reference; sampling area (sole/heel); endpoint (thinning and/or hole); individual rub counts per endpoint; range/mean if required; any deviation that could have affected results.

Method 2 adds: sample reference including size designation, any additional load used, and the leg-form size used.


Q13. Why not just test socks with the standard flat-fabric Martindale method (ISO 12947-2 / ASTM D4966)?

Because flat abrasion testing cannot replicate real sock wear. A sock is engineered to contour to a foot and is abraded while stretched and flexing inside a shoe. Flat testing ignores that stretch, curvature and tension pattern, so it can rank two yarns differently from real life. EN 13770 was written specifically to reproduce the worn geometry and the stretch state.


Q14. Why is it important for the material / the product?

  1. Heel and toe are the failure hot-spots — holes there are the number-one consumer complaint and return reason for socks; both methods target exactly those known wear areas.

  2. It captures the failure mode flat tests miss — "thinning" of plated nylon/cotton knits, where the spun yarn abrades away and only the filament skeleton remains.

  3. It quantifies design levers — fibre type and blend, yarn count, plating, loop length and density, reinforcement yarns, terry cushioning, plating and finishing treatments can all be ranked objectively with a number.

  4. It supports specifications, trade and dispute resolution — a single EU-harmonised method with mandatory report items removes ambiguity between supplier, brand and third-party laboratory.

  5. It underpins durability and sustainability claims — extended service life is now a measurable KPI in eco-design and circular-economy programmes.


Q15. Can the result be used to predict the service life of a sock in years?

Not directly. As with all laboratory abrasion tests, the result is a comparative ranking under controlled conditions, not a calendar life prediction. It becomes meaningful when correlated with wear trials or historical field data. ASTM D4966 carries the same caution for flat fabrics.


Q16. What are the biggest sources of variability, and how do I improve repeatability?

  • Conditioning — always 20 ± 2 °C / 65 ± 4 % RH (EN 20139), specimens relaxed and tension-free.

  • Mounting tension/stretch — over-stretching the knit during cutting and mounting is the classic error; use the spring-loaded block (35 N) and the correct leg-form size.

  • Abradant condition and replacement — respect the 50 000-rub (Method 1) and 500-cycle (Method 2) replacement rules; change soiled felt.

  • Operator judgement of the endpoint — use short inspection intervals near the endpoint, brush/de-pill the surface, and if possible use the same trained assessor or photographic reference standards.

  • Number of specimens — use the full sampling plan (≥4 discs per sock, or 12 tests in Method 2) and report mean and range.


Q17. How does EN 13770 relate to the ISO 12947 series and ASTM D4966?

EN 13770 uses the Martindale machine and motion of ISO 12947-1 but replaces the specimen holder with a special sock assembly. ISO 12947-2/-3/-4 (specimen breakdown, mass loss, appearance change) and ASTM D4966 are the general flat-fabric Martindale routes; GB/T 21196.1–.4 is the Chinese equivalent of the ISO 12947 series. None of them reproduces the stretch state of a worn sock, so none replaces EN 13770 for hosiery.


Q18. Is EN 13770 a pilling test?

No. Pilling is covered by EN ISO 12945-1/-2 and ASTM D4970, which use the same Martindale platform but a different test head and a completely different endpoint. EN 13770 only instructs you to cut off pills so they do not interfere with the abrasion assessment.

< Previous: EN 16094 Micro-Scratch & Polishing Resistance Test for Laminate Floor Coverings

> Next: EN 10234 Drift Expanding Test for Metallic Tubes

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.