Information on the most widely used ASTM standards within the materials testing industry
ASTM D885 Tire Cord Tester | Industrial Filament Yarn Testing Machine | UnitedTest
UnitedTest manufactures ASTM D885 compliant testing machines for tire cords, tire cord fabrics and organic industrial filament yarns. Perform tensile strength, elongation, shrinkage and physical property tests for nylon, polyester and rayon tire reinforcement materials, supporting tire factory QC, material qualification and rubber reinforcement component evaluation for hoses, conveyor belts and other rubber products.
ASTM D885 establishes a complete set of standardized test procedures for industrial filament yarns, twisted tire cords, and woven tire cord fabrics produced from manufactured organic-base fibers, including nylon, polyester, rayon and related high-performance industrial yarns. Widely adopted in the tire and rubber industry, this standard covers key mechanical property tests such as breaking force, elongation at break, tenacity, modulus and thermal shrinkage of tire reinforcement materials. Test data guides raw material incoming inspection, new product development, batch quality control and third-party material qualification for pneumatic tire manufacturers. Beyond tire applications, ASTM D885 test methods are also suitable for reinforcing cords used in rubber hoses, conveyor belts, flexible rubber linings and other engineered rubber goods, helping manufacturers verify consistency, stability and long-term mechanical performance of textile reinforcements. UnitedTest’s ASTM D885 testing system delivers stable, repeatable test results to meet laboratory accreditation and customer specification requirements.
Specific Test Methods Included:
| 1, Tensile Properties of Yarns and Cords | |
| Princile | A specimen is clamped at a defined gauge length and stretched at a controlled rate until rupture. Continuous force-elongation data is used to calculate strength, elongation, modulus, and energy absorption. |
| Test Equipment | Constant-Rate-of-Extension (CRE) type is preferred; CRL (constant-rate-of-loading) and CRT (constant-rate-of-transverse) types are permitted but have known bias relative to CRE. All machines must comply with ASTM D76 Clamps: Cam or pneumatic clamps with snubbing surfaces (≥12.5 mm diameter) to prevent jaw breaks and slippage.. |
| Test parameter |
|
| 2. Other Yarn and Cord Properties | |
| Parameter | - Twist level in yarns and cords (direct-counting method) - Cord thickness (gauge) - Extractable matter content - Dip (adhesive) solids pickup: quantifies RFL (resorcinol-formaldehyde-latex) adhesive content, with fiber-specific solvent protocols: - Nylon: 90% formic acid dissolution - Polyester: KOH reflux or trichloroacetic acid-dichloromethane dissolution - Rayon: 71% sulfuric acid dissolution - Cord-to-elastomer adhesion (referenced to ASTM D4393 and D4776) |
| Equipment |
|
| 3. Tire Cord Fabric Properties | |
| Parameter | - Fabric width - Mass per unit area - Warp end count and filling pick count - Fabric bending stiffness |
| Equipment | CRE tensile machine with 20 N load cell 25-mm span 3-point bending fixture or custom holder/depressor assembly |
Test Parameters
| CRE crosshead rate | 120 % of nominal gauge length per minute; 100 % alternate; aramid yarns use ASTM D7269 |
| CRL loading rate | Rayon 25 ± 3 (mN/tex)/s [18 ± 2 (gf/den)/min]; nylon/polyester 50 ± 7 (mN/tex)/s [35 ± 5 (gf/den)/min] |
| CRT traverse rate | 120 % of gauge length per minute; 100 % alternate |
| Gauge length | 250 ± 1 mm [10 ± 0.05 in.], alternate 500 ± 2 mm [20 ± 0.10 in.] |
| Pretension | 5 ± 1 mN/tex [0.05 ± 0.01 gf/den], or slack start |
| Load‑cell range | Estimated breaking force within 10–90 % of full scale |
| Jaw‑break rejection | Discard specimens breaking in jaws or within 10 mm [3/8 in.] of jaw nip |
| Air velocity across specimen | <250 mm/s [50 ft/min] avoids significant interlaboratory bias from the Gough–Joule effect |
| High‑strength cord clamping | Larger snubbing surfaces or powdered rosin on cord portions held between snubbing surfaces may be used |
| Zero‑twist multifilament yarn | Insert a small twist for tensile testing; historically up to 120 t/m [3.0 tpi] |
| Oven drying | 105 ± 3 °C [221 ± 6 °F]; 20–50 air changes/hour; constant mass = ≤0.1 % loss per 15 min in‑oven or 30 min out‑of‑oven weighing |
| Oven‑dried rayon | Dry 2–6 h; test within 10 ± 1 s of removal from oven; ambient exposure 10 ± 1 s |
| FASE elongations, Table 3 | Rayon 6 % greige / 3 % adhesive‑processed; Nylon 14 % / 5 %; Polyester 10 % / 5 % |
| Initial modulus | Tangent to initial straight‑line portion; force at 10 % elongation; report to nearest 10 mN/tex [0.1 gf/den] |
| Chord modulus limits, Table 4 | Rayon 30–60 mN/tex [0.3–0.6 gf/den]; Nylon 20–40 [0.2–0.4]; Polyester 30–60 [0.3–0.6]; M_c = 100(T_b − T_a)/(E_b − E_a) |
| Twist | Ten specimens; 5 ± 1 mN/tex; ASTM D1423 |
| Thickness | Five specimens of four cords; 10 mm presser foot; ~25 kPa; ~5 N tension; lower foot over ~5 s; stabilize ~5 s; read 0.01 mm [0.0005 in.] |
| Dip pickup ovens | 105 ± 3 °C and 150 ± 3 °C [302 ± 6 °F] |
| Dip pickup result | Average DPU to nearest 0.1 % |
| Stiffness | 20 N load cell; 25 mm opening; 50 mm specimen reduced to ten warp ends; crosshead 25 mm/min [1 in./min]; chart 125 mm/min [5 in./min]; bending force 10–90 % full scale; record to 1 mN [0.1 gf] |
| Elevated temperature | 177 ± 2 °C [350 ± 3 °F] |
| Wet contraction water | 24 ± 2 °C [75 ± 2 °F] |
| Growth load | 100 ± 1 mN/tex [1.0 ± 0.01 gf/den] total force after 5 ± 1 mN/tex pretension |
Related standard:
| ISO 3341 | Textile glass - Yarns - Determination of breaking force and breaking elongation; |
| ASTM D7269 | Standard Test Methods for Tensile Testing of Aramid Yarns |
| AS 2001.2.7 | METHODS OF TEST FOR TEXTILES - PHYSICAL TESTS - DETERMINATION OF BREAKING FORCE AND EXTENSION OF YARNS |
| ASTM D885 | Standard Test Methods for Tensile Properties of Tire Cords and Tire Cords Fabrics; |
| ISO 3342 | Textile glass - Mats - Determination of tensile breaking force |
| ASTM D2256 | Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method |
| ISO 2062 | Textiles; yarns from packages; determination of single-end breaking force and elongation at break |
Test Application — Industry Fields
| Pneumatic tire manufacturing | Qualification of nylon, polyester and rayon yarns, twisted cords and cord fabrics for carcass, belt and other tire reinforcement structures |
| Other rubber goods | Reinforcing cords/fabrics for conveyor belts, V‑belts, hoses, air springs and other elastomer products |
| Fiber and yarn producers | Incoming raw‑material QC, linear density, moisture regain, twist and tensile property verification |
| Cord twisting, dipping/RFL treating and weaving | Process control for twist, dip solids pickup, fabric mass, width, count and stiffness |
| Tire and rubber product engineering | Breaking force, tenacity, elongation, FASE, modulus and toughness data for reinforced‑rubber design calculations |
| Adhesion and durability evaluation | H‑test/strap‑peel adhesion between textile cord and rubber compound |
Keywords: ASTM D885 tester, tire cord testing machine, industrial filament yarn tester, tire cord fabric tensile tester, nylon tire cord test, polyester tire cord tester, rayon tire cord testing, tire reinforcement material test, rubber reinforcement cord tensile test, yarn breaking force tester, yarn elongation tester, thermal shrinkage test for tire cord, pneumatic tire material QC, conveyor belt cord test, rubber hose reinforcement yarn test, industrial textile tensile equipment, UnitedTest tire cord tester, ASTM D885 textile testing machine
Related products and device
Related Standard
ISO 3341 Textile glass — Yarns — Determination of breaking force and breaking elongation
ISO 3341 specifies a method for the determination of the tensile breaking force and elongation at break of glass yarns taken from packages.
The method is applicable to various types of glass yarn (single, folded, cabled, strands, structures without twist, rovings, etc.). It is basically intended for single, folded and cabled glass yarns having a diameter of less than 2 mm, or a linear density lower than 2000 tex, taken from packages. This test is applicable to various types of glass yarn (single, folded, cabled, strands, structures without twist, rovings, etc.). It is basically intended for single, folded and cabled glass yarns having a diameter of less than 2 mm, or a linear density lower than 2000 tex, taken from packages.
ISO 2062 specifies the method for determining the breaking force and elongation at break of textile yarns (single, piled, or cabled) under a constant rate of extension (CRE). It is a fundamental tensile test for yarn quality control.
The test operates on the principle of applying a constant rate of elongation to a single yarn specimen until it breaks:
A single yarn is securely clamped between two grips at a fixed gauge length.
The lower grip moves downward at a constant speed, stretching the yarn at a rate of 100% per minute of the gauge length.
The machine continuously records the force (load) applied and the corresponding elongation.
The test ends when the yarn breaks. The maximum force recorded is the breaking force, and the stretch at that point is the elongation at break (expressed as a percentage).
ISO 3790 — Fishing nets — Determination of elongation of netting yarns
ISO 3790 specifies a laboratory method for determining the elongation of netting yarns taken either from packages (cones, bobbins, spools) or from netting, in their final physical state — i.e., the yarn is tested as supplied/as used, without altering its structure. Tests may be run in dry or wet state, but the standard explicitly says wet-state tests are "particularly appropriate in indicating the behaviour of the yarn in use".
ISO 3342 Textile glass - Mats - Determination of tensile breaking force
ISO 3342 specifies a standardized method for measuring the tensile breaking force of textile glass mats. It is primarily intended for chopped-strand mats but is also applicable to certain types of continuous-strand mats, usually those for pultrusion processes.
ASTM D2256 is the standard test method for tensile properties of yarns by the single-strand method. It is the predominant standard used in North America and is technically very similar to ISO 2062. It quantifies breaking force, elongation at break, and derived properties (tenacity, modulus, toughness) under diverse conditions, serving as a benchmark for quality control, product development, and material specification.
Frequently Asked Questions (FAQs) – ASTM D885 Test details for Tire Cords Fabrics and Industrial Filament Yarns
A: ASTM D885/D885M is a consensus standard published by ASTM International that defines standardized test methods for evaluating tire cords, tire cord fabrics, and industrial filament yarns made from manufactured organic-base fibers (primarily nylon, polyester, and rayon). The 2025 edition covers tensile performance, physical dimensions, chemical coating content, and fabric mechanical properties for reinforcement materials used in pneumatic tires and other rubber goods.
Q2. Which materials does it cover?
Industrial filament yarns wholly made from manufactured organic‑base fibers, twisted cords made from them, woven tire cord fabrics, and other structures made specifically for pneumatic tires. The methods are explicitly relevant to nylon, polyester and rayon yarns, cords and fabrics. Section 1.1.1 also allows application to the same structures when used to reinforce other rubber goods.
Q3. Why is ASTM D885 testing important for the material? (Core answer)
Because the cord is the load‑bearing skeleton of a pneumatic tire. Section 14.2 states that the force‑bearing ability of a reinforced rubber product is related to the strength of the yarn or cord used as reinforcement, so breaking force is used directly in engineering calculations. Beyond that:
Breaking tenacity normalizes force by linear density, allowing fair comparison of different cord sizes and fiber types.
Elongation affects finished‑product uniformity and dimensional stability in service.
FASE and modulus describe how the cord responds to processing and to varying loads; FASE monitors changes during twisting, dipping, weaving and incorporation into rubber.
Work‑to‑break and breaking toughness quantify mechanical energy absorption, relevant to impact and fatigue resistance.
Moisture regain, linear density, twist, dip pickup and adhesion control whether the cord and the rubber compound actually behave as one composite. RFL dip exists to improve adhesion; dip solids pickup is a process‑control variable, and H‑test/strap‑peel adhesion reflects bond quality.
Without standardized conditioning, gauge length, speed, clamps and reporting, the "same" cord can produce different numbers in different labs. D885 creates a common measurement language for fiber producers, corders, dippers, weavers, tire makers and rubber‑goods manufacturers.
Q4. What tensile testing machine does D885 require?
A single‑strand tensile machine conforming to ASTM D76, of CRE, CRL or CRT type — with CRE (constant‑rate‑of‑extension) preferred. It needs an autographic recorder (rectilinear coordinates preferred) or electronic calculation/display, plus cam or pneumatic clamps with fixed snubbing surfaces integral with one clamping face. Snubbing surfaces may be circular with diameter not less than 12.5 mm [½ in.] or semi‑involute. Automated specimen‑loading CRE testers are permitted.
Q5. What grips are needed for high‑tenacity tire cord?
Cam or pneumatic clamps with snubbing surfaces. As cord diameter and strength increase, larger snubbing surfaces or greater holding capacity may be required to prevent slippage or excessive jaw breaks; if slippage still occurs, applying powdered rosin to the cord portions held between the snubbing surfaces has been found useful, especially for adhesive‑treated organic cords. Bollard/capstan‑type grips are the practical industry solution for cords that slip in flat jaws.
Q6. What other instruments are needed besides the universal tester?
A twist tester (ASTM D1423), thickness gauge (ASTM D1777, 10 mm presser foot, ~25 kPa), precision balance (1 mg), weighing bottles/desiccator, dip‑pickup glassware (extraction flasks, condensers, Gooch/G4 crucibles, glass‑fiber filters), a 20 N load cell plus stiffness rack/depressor or 3‑point bending fixture, H‑test mold and vulcanizing press for adhesion, and length/force devices for the X1–X3 appendices.
Q7. What gauge length and test speed are used?
Gauge length 250 ± 1 mm [10 ± 0.05 in.], with an alternate 500 ± 2 mm [20 ± 0.10 in.]. CRE crosshead rate = 120 % of nominal gauge length per minute (100 % alternate). CRL: rayon 25 ± 3 (mN/tex)/s, nylon/polyester 50 ± 7 (mN/tex)/s. CRT: 120 % of gauge length per minute (100 % alternate).
Q8. Why is rayon treated differently?
Rayon tensile properties are strongly moisture‑dependent. If actual regain is within ±0.3 % of the specification regain, report the observed value; if outside, apply a material‑specific adjustment factor derived from the slope of "breaking force vs. regain" (Section 17) or "elongation vs. regain" (Section 20). For oven‑dried rayon, dry at 105 ± 3 °C for 2–6 h, then mount and start the tester 10 ± 1 s after the specimen leaves the oven.
Q9. Breaking force vs. breaking tenacity vs. breaking toughness — what is the difference?
Breaking force is the maximum force at rupture (N or lbf). Breaking tenacity = breaking force / linear density (mN/tex or gf/den), enabling size‑independent comparison. Work‑to‑break is the area under the force–elongation curve; breaking toughness is work‑to‑break normalized by linear density (J/g or in.·lbf/in.·den), i.e. energy absorption per unit mass.
Q10. How is cord‑to‑rubber adhesion tested?
Section 34 directs you to ASTM D4393 (strap peel) or ASTM D4776/D4776M (H‑test). In the H‑test, a cord is embedded between two rubber blocks, vulcanized, conditioned and pulled axially from the rubber on a CRE tester; the maximum pull‑out force is the adhesion result. ASTM D4776‑25 conditioning is 24 ± 1 °C / 55 ± 2 % RH for at least 4 h and up to 4 days. The ISO counterpart is ISO 4647 / BS ISO 4647:2021, and China's GB/T 2942‑2009 is a modified adoption of ISO 4647:1982.
Q11. Which ASTM standards does D885 reference?
Section 2 lists D76, D123, D276, D1423, D1776, D1777, D1907, D1909, D2257, D2258, D2462, D2494, D2654, D3774, D3775, D3776, D3888, D4393, D4776, D4848, D4850, D6477 and D7269. Note that D276 was withdrawn in 2021; D885 references its last approved historical version. Closest companions: D2256 (general single‑strand yarn tensile), D7269 (aramid yarns), D4776/D4393 (adhesion), D2229 (steel cord adhesion) and D6775 (webbing/tape/braid tensile).
Require More Customized Solutions?