Home >> Application >> By Standard >> Others >> EN 826 Compression Testing Machine for Thermal Insulation

EN 826 Compression Testing Machine for Thermal Insulation

Share:

EN 826 Compression Behaviour Tester for Building Thermal Insulation | UnitedTest

UnitedTest manufactures EN 826 compression testing machines to evaluate compression performance of thermal insulating products for construction. Our equipment supports compressive stress measurement, short-term load assessment, quality control and reference data acquisition for building insulation design.


EN 826 Thermal insulating products for building applications — Determination of compression behaviour

EN 826 defines standardized equipment and test procedures to characterize the compression behaviour of thermal insulation specimens used in construction. This widely adopted European standard is suitable for various building thermal insulating materials including EPS, XPS, mineral wool, PIR and phenolic foam boards. It helps engineers and manufacturers obtain reliable compressive stress data required for subsequent compressive creep tests, assess insulation performance under short-term mechanical loads, carry out routine factory quality inspection, and collect reference test values that support structural design calculation with appropriate safety factors. Accurate compression test results ensure insulation boards used in walls, roofs and floors meet mechanical load requirements and maintain stable thermal performance over service life. UnitedTest supplies reliable EN 826 compression test instruments built for consistent, repeatable compression testing of building thermal insulation products.


Test Principle

A compressive force is applied at a given constant rate of displacement, perpendicular to the major faces of a squarely cut test specimen, and the maximum stress supported by the specimen is calculated. For tapered products, specimens are cut to obtain two parallel faces.

Two result paths are defined:

  1. If the maximum stress occurs at a strain less than 10 % — i.e. the specimen yields or ruptures before 10 % deformation — the result is compressive strength σₘ, and the corresponding strain εₘ is reported.

  2. If no failure is observed before 10 % strain, the result is compressive stress at 10 % strain σ₁₀.

EN 826 Compression Testing Machine for Thermal Insulation

Compression force - displacement curve.


Test Equipment required for EN 826 Compression Testing Machine for Thermal Insulation

Universal testing machine    

Equipped with two highly rigid, polished, plane-parallel platens (square or circular), with dimensions at least matching the specimen’s side length or diagonal. 

One platen is fixed, the other movable, optionally fitted with a central ball joint to ensure purely axial loading. 

The machine must deliver a consistent, adjustable constant displacement rate.

Force sensor

Mounted on one platen, with a measurement accuracy of ±1%. Its own deformation under load must be negligible compared to specimen deformation, or corrected via calculation.

Displacement measurement systems

Provides continuous displacement reading with an accuracy of ±5% or ±0.1 mm, whichever is smaller.

Recording device

Simultaneously records force and displacement data to generate a force-displacement curve, which also supports calculation of the compression modulus of elasticity.

Special Apparatus for Cellular Glass

Compression machine must be fitted with a ball joint for uniform load distribution.

Additional surface preparation tools: hot bitumen bath with application roller, plaster application tools, flat steel plates and load distribution weights.


Test Specimen Information:

General Specimen Requirements

  • Dimensions: Specimens retain the original product thickness; specimen width must be no less than its thickness. Standard nominal sizes: 50×50 mm, 100×100 mm, 150×150 mm, 200×200 mm, 300×300 mm. The exact size is specified in the relevant product standard or agreed between interested parties.

  • Quantity: Minimum 5 specimens when no product standard specifies a sample size.

Cellular Glass Specimens

  • Size: Ideally a quadrant cut from a full slab (e.g. 300×225 mm from a 600×450 mm slab); alternatively 200×200 mm specimens taken one per slab quadrant to preserve material symmetry.

  • Surface preparation: Bearing faces are pore-filled and smoothed with hot bitumen grade R 85/25 (heated to 170 ± 10 °C, applied at ~1 ± 0.25 kg/m²) or a 2 ± 1 mm plaster layer. A thin release sheet is used to prevent adhesion to test platens. Faced cellular glass boards do not use bitumen preparation.


Test Parameters & Stipulations

ParameterGeneral RequirementCellular Glass
Test temperature(23 ± 5) °C; (23 ± 2) °C / 50±5% RH for dispute testingSame as general
Preload stress(250 ± 10) Pa; 50 Pa permitted if specified for highly deformable materialsSame as general
Displacement rate0.1 d per minute (±25%), where d = specimen thickness in mm0.01 d per minute (±25%)
Test terminationAt yield/rupture (<10% strain) or at 10% strainAt specimen fracture (marked load drop + audible breakage)
Force measurement accuracy±1% of reading±1% of reading


Test Procedures for EN 826 Compression Testing Machine for Thermal Insulation

  1. Measure all linear dimensions of the specimen in accordance with EN 12085.

  2. Center the specimen precisely between the two platens of the compression machine.

  3. Apply a preload of (250 ± 10) Pa to establish the zero-deformation reference point.

  4. Compress the specimen at a constant displacement rate of 0.1 d per minute.

  5. Continue loading until the specimen yields (for compressive strength determination) or until 10% strain is reached (for stress at 10% strain).

  6. Continuously record the force-displacement curve throughout the full test duration.


Industry Application Fields

EN 826 is primarily a building-construction thermal insulation test method. Its results are used by:

  • Insulation manufacturers for factory production control, batch release, product development and type testing;

  • Accredited/third-party laboratories for certification and comparative testing;

  • CE-marking / Declaration of Performance (DoP) bodies under harmonised product standards such as the EN 13162–EN 13171 series; EN 13165, for example, calls up EN 826 for compressive strength/σ₁₀ of PUR/PIR boards.

  • Specifiers, structural engineers and designers to obtain reference values, apply safety factors, and select products for load-bearing insulation layers;

  • Researchers studying mechanical behaviour, anisotropy and structure–property relationships.

Typical products/materials: EPS, XPS, PUR/PIR, phenolic foam, mineral wool, cellular glass, rigid boards, fibre-based and load-bearing insulation products.

Typical applications: floor insulation, flat and walkable roofs, rooftop car parks, industrial floors, cold stores, screeds, floating floors, sandwich-panel cores, façade/wall systems, and building equipment/industrial installations. It is also used to set the stress level for compressive creep testing to EN 1606 and for applications with short-term loads such as floors and walkable roofs.


Related Standard: 

ISO 844Rigid cellular plastics – Determination of compression properties.
ISO 29469Thermal insulating products for building applications — Determination of compression behaviour
ISO 1209-1Rigid cellular plastics – Determination of flexural properties.
ISO 1209‑2Rigid cellular plastics - Determination of flexural properties - Part 2: Determination of flexural strength and apparent flexural modulus of elasticity
ASTM D5379

V-notched beam shear test method for composite materials, used for alternative shear characterization.

ISO 1922Rigid cellular plastics - Determination of shear properties
ASTM C165
Compressive properties of thermal insulations, including fibrous materials; reports resistance at 10 % and 25 % deflection, whereas EN 826 reports σₘ/σ₁₀ and E.
JIS K 7220硬質発泡プラスチック―圧縮特性の求め方
EN 12090Thermal insulating products for building applications. Determination of shear behaviour
ASTM C393

Standard Test Method for Core Shear Properties of Sandwich Constructions by Beam Flexure

ASTM C365Flatwise Compressive Properties of Sandwich Cores; determines core compressive strength and modulus for sandwich-panel design, including foam and honeycomb cores. 
ISO 7616Compressive-creep methods for rigid cellular plastics; relevant when long-term deformation under sustained load matters.
ASTM C203Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
EN 1605deformation under compressive load + temperature
ISO 1856Flexible cellular polymeric materials / flexible foam compression-set or compression testing; not substitutes for rigid-foam D1621.
ASTM D1621Standard Test Method for Compressive Properties of Rigid Cellular Plastics
GB/T 8813Chinese national standard Rigid cellular plastics—Determination of compression properties, identical to ISO 844:2014 (IDT)
EN 826Thermal insulating products for building applications — Determination of compression behaviour; product/application-oriented rather than a general rigid-foam material method. 


Keywords: EN 826 compression tester, thermal insulation compression behaviour test, building insulation compressive strength test machine, EPS XPS mineral wool compression test, construction thermal insulating material compression test, compressive stress test for insulation, short-term load test of insulation board, insulation compression creep pre-test, building material quality control tester, foam insulation compression test equipment, UnitedTest compression testing machine, , construction insulation design reference testing

Related products and device

EN 826 Thermal Insulation Material Compression Test Universal Testing Machine

A single column tensile tester is a sophisticated material testing instrument designed for measuring mechanical properties of various materials under tension, compression, bending, shear, and other loading conditions. As the name suggests, it features a single vertical column supporting a moving crosshead that applies force to test specimens.

EN 826 EPS XPS mineral wool compression test

UnitedTest manufactures and exports compressive shear test fixtures, ISO 6238 wood adhesive shear jigs, ASTM D905 block shear fixtures, ASTM D4501 rigid‑substrate shear tools, and compatible universal testing machines. Buy ISO 6238 and ASTM D905 compressive shear test fixtures from UnitedTest.

insulation compression creep pre-test, building material quality control tester

Vice Tensile test fixture for plastics is based on the test standatd ASTM D638, determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, speed.

Related Standard

ASTM D905 Wood Adhesive Compression Shear Test –

ASTM D905 Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading

ASTM D905 evaluates comparative shear strength of adhesive bonds, mainly wood-to-wood, using a compressed block/shear specimen. It comparative shear performance of laboratory‑prepared wood‑to‑wood adhesive joints under compressive force; it is intended for adhesive screening, R&D and process monitoring rather than direct design‑strength calculation for finished structural products.

ASTM D906 Tensile Shear Test for Plywood Adhesive Bonds –

ASTM D906 Standard Test Method for Strength Properties of Adhesives in Plywood Type Construction in Shear by Tension Loading

ASTM D906 specifies a tensile-loading method for determining the comparative shear strength of wood-to-wood adhesives in plywood-type (three-ply cross-laminated) construction. It measures comparative shear strength of wood-to-wood adhesives exclusively for cross-laminated plywood-style three-ply veneer assemblies. Not designed for finished consumer wood products or parallel single-grain laminated joints.

ISO 6237 Tensile Shear Test for Wood-to-Wood Adhesive Bonds –

ISO 6237 Adhesives – Wood-to-wood adhesive bonds – Determination of shear strength by tensile loading.

ISO 6237 specifies a laboratory method for determining the shear strength of wood-to-wood adhesive bonds using a standard specimen loaded in tension under strictly defined conditions of preparation, conditioning, and testing. It is intended only for adhesives used in bonding wood to wood in either parallel-laminated or cross-laminated construction, and is not intended for testing manufactured/finished products.

ISO 27528 screw withdrawal resistance test of wood-based panels –

ISO 27528 defined to measure the maximum axial pull-out force required to extract screws from wood composite panels, covering two core test modes: face screw withdrawal and edge screw withdrawal. It serves as a global unified test method for evaluating the screw holding capacity of fibreboard, particleboard, OSB, plywood and other engineered wood panels with thickness ≥ 15 mm.

ASTM D1761 Test Methods for Mechanical Fasteners in Wood –

ASTM D1761 test methods provide a basic procedure for evaluating the withdrawal and lateral resistance of fasteners installed in wood and wood-based materials. The tests also provide a basis for determining comparable performance of different types and sizes of fasteners installed in wood and wood-based materials.  Quantify the mechanical connection performance of nails, staples, screws, bolts, lag screws and timber connectors embedded in solid wood, plywood, OSB, fiberboard and other wood-based composites. Spikes are classified as nails within this standard.

ASTM D1037 Test Methods for Wood-Base Fiber and Particle Panel Materials –

ASTM D1037 - Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials 


ASTM D1037 test methods cover the determination of the properties of wood-base fiber and particle panel materials that are produced as mat-formed panels such a particleboard, medium density fiberboard, hardboard, and oriented strand board.


ASTM D1037 test methods cover small-specimen tests for wood-base fiber and particle panel materials that are made to provide: Data for comparing the mechanical and physical properties of various materials,

Data for determining the influence on the basic properties of such factors as raw material and processing variables, post-treatments of panels, and environmental influences, and

Data for manufacturing control, product research and development, and specification acceptance.

ASTM D897 Tensile Test of Adhesive Bonds –

ASTM D897 prescribed a method for determining the comparative tensile properties of adhesive bonds in a standard specimen when tested under specific conditions. Its primary purpose was to measure the tensile strength of an adhesive bond between two rigid substrates (metal to metal). 

ASTM D1002 Lap Shear Test of Adhesively Bonded Metal Specimens –

ASTM D1002 is the most widely used standard test for measuring the apparent shear strength of metal‑to‑metal adhesive single‑lap joints under tension loading. It provides comparative data for adhesive selection, process control, and quality assurance in structural bonding applications. It is the most common test for evaluating adhesive shear performance.

ISO 1922 Shear Properties Test for Rigid Cellular Plastics –

ISO 1922 Rigid cellular plastics – Determination of shear properties

ISO 1922 defines a standardized procedure to measure shear strength of rigid cellular plastics, and additionally provides methods to calculate shear modulus and shear strain at fracture.


ASTM D1621 Rigid Cellular Plastics Compression Testing –

ASTM D1621 Standard Test Method for Compressive Properties of Rigid Cellular Plastics

ASTM D1621 determining the compressive properties of rigid cellular materials, expanded/rigid plastic foams, particularly expanded plastics. It compresses a conditioned foam specimen between two flat platens at a controlled speed and records a complete load–deflection curve.

EN 826 Compression Test: Frequently Asked Questions (FAQs)

Q1. What is the EN 826 test?

A: EN 826:2013, Thermal insulating products for building applications — Determination of compression behaviour, is the CEN method for short-term uniaxial compression of building insulation. A square, full-thickness specimen is loaded perpendicular to its major faces at a constant displacement rate while force and displacement are recorded. It reports compressive strength σₘ when yield/rupture occurs below 10 % strain, or compressive stress at 10 % strain σ₁₀ when no failure occurs, and optionally the compression modulus E. EN ISO 29469:2022 / ISO 29469:2022 now supersedes EN 826:2013, but many legacy product standards and specifications still call it up.


Q2. Why is the EN 826 compression test important?

A: Insulation performance depends on thickness. If a floor, roof or screed load crushes the board, thickness and thermal resistance fall, so U-values and energy demand rise. EN 826 qualifies load-bearing insulation, supports factory production control, CE marking / Declaration of Performance evidence and material comparison, and provides reference values from which short-term design values are derived with safety factors. It also defines the compressive stress used to set up EN 1606 compressive creep tests. In short: it protects both mechanical integrity and the thermal performance the product was bought for.


Q3. Which insulation materials and applications use EN 826?

A: Building thermal insulation products including EPS, XPS, PUR/PIR, phenolic foam, mineral wool / stone wool boards, cellular glass, rigid foam boards, fibre-based products and load-bearing insulation panels. Typical applications are floor insulation, flat and walkable roofs, rooftop car parks, cold stores, industrial floors, screeds, floating floors, façade systems and sandwich-panel cores. Independent labs, insulation manufacturers, certification bodies and design engineers all use the data.


Q4. Should I report compressive strength σₘ or compressive stress at 10 % strain σ₁₀?

A: It depends on the curve, not on preference. If the maximum force Fₘ is reached at yield or rupture before 10 % strain, report σₘ = 10³·Fₘ/A₀ in kPa together with εₘ = Xₘ/d₀ × 100 %. If the specimen keeps deforming with no failure before 10 % strain, report σ₁₀ = 10³·F₁₀/A₀ in kPa. Do not mix the two in one data set: they describe different failure behaviours and mixing creates false scatter. Results are means expressed to three significant figures and must not be extrapolated to other thicknesses.


Q5. Why does EN 826 use 10 % strain, and can I calculate stress at lower strains?

A: Many foam and fibrous insulation products do not show a clear yield point — they crush progressively. A fixed 10 % relative deformation gives a reproducible stress point for products that never fail, which is why σ₁₀ is the declared compressive value for most insulation boards. EN 826 also allows compressive stress at strains lower than 10 % to be calculated if required, and the optional compression modulus E is taken from the linear elastic part of the F–X curve below the proportional limit.


Q6. Is EN 826 the same as ISO 844, ASTM D1621 or ASTM C165?

A: Similar, but not identical. ISO 844:2026 covers rigid cellular plastics and defines Procedure A (platen/crosshead displacement) and Procedure B (extensometer on the specimen). ASTM states that ASTM D1621-16(2023) is technically equivalent to ISO 844. ASTM C165 reports compressive resistance at 10 % and 25 % deflection for thermal insulations. EN 826 uses full product thickness, 50–300 mm square specimens, σₘ / σ₁₀ / E and product-standard-driven sampling. Specimen geometry, rate expression, end point and reported quantities differ, so results are not automatically interchangeable. Always run the standard named in your product specification or by your certification body.


Q7. What is the difference between EN 826 short-term compression and EN 1606 compressive creep?

A: EN 826 is a short-term test: load to yield or 10 % strain in a few minutes and report σₘ or σ₁₀. EN 1606 determines compressive creep — the long-term reduction in thickness under a sustained compressive load over the product's service life. EN 826 is used to select or define the stress level applied in creep testing; it does not replace creep data for permanently loaded floors, roofs or cold stores. For sustained loads, specify both tests.


Q8. What should I specify when buying an EN 826 / EN ISO 29469 testing machine from UnitedTest?

A: Specify: force capacity matched to expected σ₁₀ × loaded area; platens at least as large as the biggest specimen diagonal (a 300 × 300 mm specimen needs ≥ 424 mm); polished plane-parallel faces; one fixed and one movable plate with spherical seat/ball joint; a load cell and calibration meeting ±1 %; displacement measurement meeting ±5 % / ±0.1 mm; software that records F–X, applies the (250 ± 10) Pa preload and zero-deformation correction, auto-calculates σₘ, εₘ, σ₁₀ and E, exports individual and mean values, and supports 0.1 d/min ±25 % plus 0.01 d/min for cellular glass; and report templates referencing EN 826:2013 / EN ISO 29469:2022. UnitedTest also provides custom fixtures for related ISO, ASTM and EN methods.


Q9: What specimen sizes are used in EN 826?

A: Standard specimen sizes are: 50×50 mm, 100×100 mm, 150×150 mm, 200×200 mm, and 300×300 mm. The exact size is specified in the relevant product standard or agreed between parties. Specimens must retain the original product thickness, and the width must be no less than the thickness.


Q10: What is the preload in EN 826 and why is it used?

A: A preload of (250 ± 10) Pa is applied to establish the zero-deformation reference point. This ensures consistent contact between the platens and the specimen, eliminating slack and surface irregularities from the measurement. For highly deformable materials, a 50 Pa preload may be used if specified in the product standard.


Q11: Why choose UnitedTest as Manufacturer of EN 826 Compression Test Equipment? 

A: UnitedTest designs and manufactures high-precision compression testing machines fully compliant with EN 826:2013 for thermal insulation materials. Our EN 826 test systems deliver accurate, repeatable compressive strength and compressive stress at 10% strain measurements for all types of building insulation products — from rigid foam boards and mineral wool to cellular glass.

Why Choose UnitedTest EN 826 Testing Machines?

✅ Full EN 826 Compliance: Meets all requirements of EN 826:2013, including force accuracy ±1%, displacement accuracy ±0.1 mm, and programmable constant displacement rates of 0.1 d/min and 0.01 d/min for cellular glass testing per Annex A.

✅ Wide Force Range: Available in 5 kN, 10 kN, 25 kN and 50 kN configurations to cover all thermal insulation materials from soft mineral wool to high-strength cellular glass.

✅ Precision Platens & Ball Joint: Rigid, polished plane-parallel platens in multiple sizes (100 mm, 200 mm, 300 mm) with self-aligning ball joint ensure uniform axial loading — essential for reliable EN 826 test results.

✅ Integrated Data Acquisition: Simultaneous force-displacement recording with automatic calculation of compressive strength (σₘ), compressive stress at 10% strain (σ₁₀), strain at maximum force (εₘ), and compression modulus of elasticity (E).

✅ Annex A Ready: Supports the full cellular glass test method including slower displacement rates and specialized specimen preparation workflows.

✅ Built for Quality Control & R&D: Ideal for insulation manufacturers, third-party testing laboratories, and research institutions performing EN 826 quality control, product certification, and material development.

Applications

  • EPS, XPS, PUR, PIR foam board compression testing

  • Mineral wool and stone wool compressive behaviour testing

  • Cellular glass compression testing (Annex A compliant)

  • Phenolic foam, perlite and calcium silicate insulation testing

  • Floating floor insulation load performance verification

  • Product CE marking and factory production control (FPC)

UnitedTest compression testers are trusted by insulation manufacturers and testing laboratories across Europe and worldwide for reliable EN 826 test results, robust construction, and intuitive operation.

< Previous: EN 12090 Shear Test for Thermal Insulating Products

> Next: EN 1447 long-term internal pressure test for GRP, GRE and fiberglass pipes

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.