Information on the most widely used ASTM standards within the materials testing industry
ISO 8492 Metallic Tube Flattening Test Machine | UnitedTest
UnitedTest manufactures ISO 8492 compliant flattening testers for circular metallic tubes. Evaluate plastic deformation capacity and detect internal defects of metal pipes with controlled flattening distance and weld positioning per product requirements.
ISO 8492 Metallic materials specifies the tube flattening test to assess the plastic deformation capability of circular cross-section metallic tubes, while exposing hidden material and weld defects. The standard regulates the flattening operation procedure, and key parameters such as flattening distance H, weld placement and failure criteria are defined by corresponding product standards or purchase specifications. UnitedTest supplies robust metal tube flattening test rigs for steel pipe mills, metal component factories and material inspection laboratories.
Test Principle:
A tube specimen or tube‑end is compressed plastically between two parallel rigid platens, perpendicular to the tube longitudinal axis, until the platen‑to‑platen distance under load reaches the value H specified in the corresponding product specification. For close‑flattening requirements, the inner surfaces of the flattened sample shall make contact over at least half of the flattened internal width b. The test evaluates plastic‑deformation capacity and exposes surface / subsurface defects such as cracks, laps or weld imperfections.
Test Specimen Information:
| Form | A ring of specified length cut perpendicular to the tube axis, or the end of a full-length tube |
| Length L | ≥ 10 mm and ≤ 100 mm |
| Edges | May be rounded by filing or chamfered by other methods |
| Note | Non-rounded / non-chamfered edges are permissible if the test result still meets the requirements (i.e. you can only "re-test with prepared edges" after a failure, not to excuse a failure) |
| Test on tube end | Cut at right angles to the tube axis, at a distance from the tube end equal to the test piece length, to a depth of at least 80 % of the outside diameter (i.e. a nearly severed ring still attached to the tube) |
| Welded tube | Weld position must be as required by the relevant product standard (typically 90° to the loading direction) |
| Preparation | No machining of surfaces; cut faces must be square to the axis |
ISO 8492 Metal Tube Flattening Test required Testing Equipment:
| Test Machine | A test machine (compression/press or universal testing machine) capable of flattening the test piece to the prescribed distance H. The machine must be able to control/limit the platen travel rate (needed for the 25 mm/min requirement in disputes). |
| Compression platens | Two platens that must be:
Platen width must exceed the width of the flattened test piece — at least 1.6 D. Platen length must extend over the whole length of the test piece.. |
Key Parameters and Stipulations
| Symbol | Designation | Unit |
|---|---|---|
| a | Tube wall thickness | mm |
| D | Tube outside diameter | mm |
| H | Distance between platens under applied load | mm |
| L | Specimen length | mm |
| b | Internal width of flattened piece | mm |
Applicable tube limits: outer diameter D ≤ 600 mm; wall thickness ≤ 15 % D. Product standards may further restrict this dimensional range.
Pass/fail is qualitative and visual: no cracks, no breaks, no separation, no lamination, no "orange-peel" surface, no weld opening — judged with the unaided eye.
Edge cracking is tolerated (Clause 6.6); cracking originating from the deformed flanks or the weld is not.
H, weld orientation, and any additional acceptance criteria (e.g. "no crack > x mm") must be taken from the product standard/purchase order.
Key Test Procedures:
Place specimen centrally between the two platens.
For welded tubes: position the weld location following the relevant product‑standard requirement.
Compress the specimen by moving platens perpendicularly to tube longitudinal axis until target loaded platen distance H is achieved.
Examine the specimen for cracks without magnification. Minor edge cracking does not cause rejection. Acceptance criteria are subject to product‑standard rules; if no criteria are given, specimen passes if no visible cracks appear under naked‑eye inspection.
Issue a test report when required by product specifications. Mandatory report contents: standard reference (ISO 8492), specimen identification, specimen dimensions, loaded platen gap H, weld position (if welded tube), and final test result (pass/fail).
Industry Application Fields:
ISO 8492 is a horizontal method standard, so it is invoked by product standards across many sectors:
Steel tube & pipe manufacturing — seamless and welded (ERW/HFI, SAW) carbon, alloy and stainless tube: routine quality-control and batch-release test, often run at least once per production hour on welded tube lines.
Boilers, pressure vessels and heat exchangers — e.g. ASME SB-338 titanium condenser/heat-exchanger tubing requires a flattening test (and a flaring test) to verify ductility and detect tiny cracking flaws.
Oil, gas and petrochemical — line pipe, casing/tubing, process and instrumentation tubing; typical QC packages combine flattening + tensile + impact + chemical analysis.
Power generation and nuclear — boiler, superheater, feedwater and condenser tubing.
Shipbuilding and offshore — class societies (e.g. CCS-recognised labs) require flattening and drift-expanding tests on tubes for ships, offshore platforms and port machinery.
Automotive and refrigeration — brake/fuel/hydraulic lines, air-conditioning and condenser tube (Cu and Cu-alloy tube uses ASTM B968/B968M).
Construction and structural steelwork — structural hollow sections and scaffolding/guardrail tube where the product standard calls up flattening.
Aerospace and special alloys — titanium and nickel-alloy tubing.

Related standard:
| EN 10232 | Metallic Materials - Tube (in Full Section) - Bend Test |
| IS 2328 | (India standard) — corresponds to ISO 8492 |
| ASTM B968 | flattening of copper and copper-alloy pipe and tube. |
| ISO 7438 | General bend test for flat metal strip/sheet specimens. |
| TCVN 5891 | Metallic materials. Tube (in full section).Bend test |
| ISO 8491 | Tube (in full section) bend test, bend rather than flatten |
| ISO 8492 | Metallic materials. Tube. Flattening test |
| ISO 8493 | Metallic materials - Tube - Drift-expanding test |
GOST 8695 | Metal pipes. Flattening testing method |
| EN 10233 | Metallic materials. Tube. Flattening test |
| GB/T 246 | Metallic materials—Tube—Flattening test |
| DIN 50136 | German Flattening test |
Why This Test Matters for a Material
It is a direct measure of transverse ductility / formability. The tensile test gives elongation along the axis; flattening imposes severe bending + through-thickness strain across the tube, simulating what actually happens when tube is bent, crimped, coiled, expanded into a tubesheet, or flattened in service. A material can pass tensile elongation and still fail flattening if it is anisotropic or has poor through-thickness ductility.
It is an excellent defect detector. Because the outer surface is stretched to a small radius, the test opens up and exposes: seams, laps, slivers, inclusions, blisters, delamination, laminations, porosity, quench cracks and coarse-grain/overheated structure. Many of these are invisible to visual inspection and marginal to ultrasonic or eddy-current testing.
For welded tube it is the reference weld-quality test. Placing the weld at the point of maximum bend reveals lack of fusion, incomplete penetration, weld/HAZ embrittlement, and mismatch. It is why welded-tube product standards (and ASTM A370's reverse-flattening variant for the ID) insist on it.
It verifies the whole manufacturing route — melting/cleanliness, hot and cold working, weld parameters, heat treatment (annealing/normalising) and straightening. A batch that has been over-cold-worked without adequate annealing, or embrittled by ageing/hydrogen/sensitisation, will crack.
Keywords: ISO 8492 tester, metallic tube flattening test machine, metal pipe flattening tester, steel tube flattening test rig, circular metal tube deformation test equipment, welded pipe flattening defect inspection machine, metal tube plastic deformation tester, alloy tube flattening test fixture, pipe weld quality verification tester, metal tubing mechanical property test system, seamless tube flattening testing machine, tubular product qualification test equipment
Related products and device
Related Standard
ISO 8491 define a unified bend test method for evaluating the plastic bending ductility of circular full-section metallic tubes, exclusively for tubes with outer diameter D ≤ 65 mm (product standards may narrow this diameter range further).
Main Industry fields: boilers & pressure vessels, oil & gas pipelines, automotive (exhaust/chassis tubing), heat exchangers, structural steel tubing, power generation (including nuclear).
EN 10233 Metallic materials. Tube. Flattening test
EN 10233 determines the ability of metallic tubes of circular cross-section to undergo plastic deformation by flattening. Also used to reveal defects in the tube (laminations, weld flaws, cracks, lack of soundness). Applicable to tubes with outside diameter D ≤ 600 mm and wall thickness T ≤ 15 % of D.
EN 10232 is the European version of ISO 8491,defines a unified cold bend test for intact circular full-section metallic tubes, designed to quantify plastic bending ductility for tubes with outer diameter D ≤ 65 mm.
ASTM A500 covers carbon steel tubing in round, square, rectangular, or special shapes, primarily used for welded, riveted, or bolted construction in bridges, buildings, and general structural applications. It specifies four mandatory test categories, tension test, flattening test, Chemical Composition Analysis and Dimensional & Visual Inspection. For us, will focus on the mechanical test.
ASTM D2105 Standard Test Method for Longitudinal Tensile Properties of "Fiberglass" (Glass‑Fiber‑Reinforced Thermosetting‑Resin) Pipe and Tube
ASTM D2105 determine the comparative longitudinal tensile properties of a fiberglass pipe specimen by pulling it in axial tension to failure under defined conditioning, temperature, and machine‑crosshead‑speed conditions.
ASTM F2663 Standard Test Method for Bead Unseating of Tubeless Passenger and Light Truck Tires
ASTM F2663 quantify the resistance of tubeless tires against bead unseating, which means the tire bead slipping off the rim flange leading to sudden air loss. It covers passenger tires, light‑truck tires, and temporary spare tires. It only defines test methodology, not mandatory performance limit values for tires.
ASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A370 test methods cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.
Covering tests like Tension, Bend, Hardness, Brinell, Rockwell, Portable, and Impact, each catering to distinct aspects of mechanical property assessment. Moreover, it accommodates annexes for specific product types, including Bar Products, Tubular Products, Fasteners, Round Wire Products, and more, ensuring a holistic approach to testing.
ISO 8493 Metallic materials - Tube - Drift-expanding test
ISO 8493 specifies a method for determining the ability of metallic tubes of circular cross-section to undergo plastic deformation in drift expansion.
Applicability limits (default, unless the relevant product standard narrows them further):
Outside diameter D ≤ 150 mm (≤ 100 mm for light metals such as aluminium alloys)
Wall thickness a ≤ 10 mm
Frequently Asked Questions (FAQ) for ISO 8492 Metallic Tube Flattening Test
Q1. What exactly is the ISO 8492 test?
A: ISO 8492:2013 (Metallic materials — Tube — Flattening test) is an international method standard that specifies how to flatten a ring or tube end between two parallel platens to determine whether a metallic tube of circular cross-section can undergo plastic deformation without cracking, and to reveal hidden defects. It is a technology / ductility test, not a strength test — no force value is reported.
Q2. Why is the flattening test so important for tube materials?
A: For four reasons:
It measures transverse ductility — the tensile test only measures elongation along the axis; flattening bends the tube wall to a tight radius across the tube, which is what really happens in bending, crimping, coiling and tubesheet expansion.
It is a defect detector — the severe stretching at the flanks opens up seams, laps, inclusions, laminations, blisters, quench cracks and coarse-grain structure that visual, UT or eddy-current inspection often miss.
It is the reference weld test — for welded tube, positioning the weld at the point of maximum bend exposes lack of fusion, incomplete penetration and HAZ embrittlement.
It validates the whole production route — melting cleanliness, hot/cold working, weld parameters and final heat treatment. An over-cold-worked or badly annealed batch cracks immediately.
Q3. Which tubes are covered by ISO 8492?
A: Tubes with outside diameter ≤ 600 mm and wall thickness ≤ 15 % of the outside diameter (a ≤ 0.15 D). The applicable range may be narrowed further by the relevant product standard. Outside these limits the method is not valid unless the product standard says otherwise.
Q4. What is the test specimen?
A: A ring 10 mm to 100 mm long, cut perpendicular to the tube axis. Edges may be rounded or chamfered (but non-prepared edges are allowed if the result still passes). For testing on a full-length tube end, cut square to the axis at a distance equal to the specimen length, to a depth of at least 80 % of the OD.
Q5. What is "H" and who decides its value?
A: H is the distance between the platens measured under load — the flattening severity. ISO 8492 does not give a number. H (often a fraction of D, e.g. 2/3 D, or calculated from a ductility constant e) must come from the relevant product standard or purchase order. Always measure it under load, not after unloading.
Q6. What is "close flattening"?
A: The most severe variant: flattening continues until the inner surfaces touch over at least half of the internal width b of the flattened specimen (Figure 1 c of the standard). Used when the product standard demands full closure.
Q7. How is pass/fail judged?
A: According to the product standard. If the product standard is silent, the specimen passes if no cracks are visible to the unaided eye (no magnifying aids). Slight cracking at the edges is not a cause for rejection — it is a cutting artifact.
Q8. Where must the weld be positioned?
A: As required by the product standard — typically at 90° to the loading direction so the weld sits at the point of maximum bend. (ASTM A370's reverse flattening variant is the complementary test that stresses the ID surface.)
Q9. How does it differ from a tensile, bend or drift-expanding test?
A: Tensile gives strength/elongation along the axis; ISO 8491 bend tests the full section in bending; ISO 8493 drift-expanding expands the end with a conical mandrel ("will it crack when expanded"); ISO 8492 flattens ("will it crack when compressed/formed"). They are complementary and usually specified together in tube product standards.
Q10. Is ISO 8492 the same as EN 10233, ASTM A370 or GB/T 246?
A: BS EN ISO 8492:2013 / EN ISO 8492:2013 are identical adoptions of ISO 8492:2013. GB/T 246-2017 is an identical (等同) Chinese adoption. EN 10233 / DIN 50136 and ASTM A370 (§A2.5.1.1) are functionally equivalent methods with their own H formulas and specimen rules — always check which one your customer's spec calls up.
Q11. Which industries require it?
A: Steel tube/pipe mills (welded line QC, often hourly), boilers & pressure vessels, heat exchangers & condensers (e.g. ASME SB-338 Ti tubing), oil & gas, power generation, shipbuilding/offshore (class societies), automotive & refrigeration tubing, structural hollow sections, aerospace and third-party certification labs.
Q12. What causes a specimen to fail?
A: Low ductility from over-cold work or inadequate annealing; weld defects or HAZ embrittlement; non-metallic inclusions and segregation; seams/laps from piercing or rolling; excessive wall-thickness-to-diameter ratio; hydrogen embrittlement or sensitisation; incorrect weld orientation or too-fast platen speed.
Q13. I need to buy a machine — what should I look for?
A: Enough capacity to flatten your largest OD and heaviest wall to close flattening; platen width ≥ 1.6 D and length ≥ 100 mm; rigid, hardened, parallel platens; closed-loop speed control down to ≤ 25 mm/min; displacement measurement of H under load; software that records D, a, L, H, weld position and produces an ISO 8492-conformant report; and compliance/verification to ISO 7500-1 force accuracy. (See the UnitedTest section below.)
Q14. Why choose ISO 8492 Tube Flattening Test Machine from UnitedTest?
A: UnitedTest supplies ISO 8492‑compliant tube flattening test machines & custom flattening fixtures for seamless & welded metallic tubes. Perform ring flattening test to evaluate tube ductility and detect weld defects for steel, stainless steel, copper & alloy tubes.
UnitedTest is a professional manufacturer of material testing machines, providing complete testing solutions for ISO 8492:2013 metallic tube flattening test. Our universal testing machines (electromechanical & hydraulic UTM) with dedicated flattening platens / fixtures fully comply with ISO 8492 requirements for circular metallic tube ring flattening testUnitedTest.
The ISO 8492 flattening test is a core quality‑control procedure for steel pipe, boiler tube, heat‑exchanger tube, pressure pipeline and non‑ferrous alloy tube manufacturers. It assesses tube plastic deformation performance and exposes hidden weld defects, laps and cracks by compressing tube ring specimens between two rigid parallel platens.
UnitedTest ISO 8492 flattening test systems support:
✅ Specimen dimension range: 10 mm‑100 mm specimen length, tube outer diameter up to 600 mm
✅ Controlled compression speed up to 25 mm/min for dispute‑condition testing
✅ Accurate measurement of platen‑to‑platen distance H under loaded condition
✅ Large‑size custom platens meeting ≥ 1.6 D width requirement
✅ Test software for automatic data logging, test‑report generation following ISO 8492 reporting clauses
✅ Suitable for seamless tubes, ERW welded tubes, stainless steel tubes, copper, aluminum and titanium alloy tubes
Our flattening test fixtures can be fitted onto our standard WDW electromechanical universal testers and hydraulic UTM series machines. No need to purchase standalone dedicated flattening equipment; you can reuse existing compression‑capable test frames with our custom platens and tooling.
Whether you run incoming‑lab quality inspection, production‑line batch acceptance, third‑party laboratory testing or material R&D, UnitedTest delivers reliable ISO 8492‑compliant tube flattening test equipment. Our engineering team can customize platen size, force capacity and test workflows according to your tube product standards and local regulatory requirements.
< Previous: ISO 8491 Metal Tube Bend Test
Require More Customized Solutions?