Home >> Application >> By Standard >> ISO >> ISO 10000~19999 >> ISO 13445 Block Shear Test — Adhesive Shear Strength Tester for Rigid Substrates

ISO 13445 Block Shear Test — Adhesive Shear Strength Tester for Rigid Substrates

Share:

ISO 13445 Block-Shear Tester for Adhesive Bond Shear Strength | UnitedTest

UnitedTest produces ISO 13445 block-shear testing machines to measure shear strength of adhesive bonds on rigid substrates, suitable for machinable and non-machinable high-modulus substrates for adhesive formulation validation and quality control.


ISO 13445 Adhesives — Determination of shear strength of adhesive bonds between rigid substrates by the block-shear method. ISO 13445 determines the shear strength of adhesives used to bond materials whose elastic modulus is higher than that of the adhesive. It gives an estimate of adhesive shear strength on both machinable and non-machinable substrates, supporting lab material screening, production batch inspection and qualification testing for structural and industrial adhesive systems.


Definitions:

  • Shear stress — force applied parallel to a flat adhesive joint, divided by the bond area.

  • Shear strength — the maximum shear stress sustained by the joint during the test.


Test Principle

Blocks, plates or disc‑shaped rigid adherends are bonded together. A shear force parallel to the adhesive bond plane is applied to shear the bonded assembly apart. The maximum failure force is recorded, and shear strength is calculated from maximum force divided by bond area. This test is especially suitable for parts that are difficult to machine, such as ceramics, glass, magnetic mouldings and rigid plastics with flat bonding surfaces.


Test Equipment required for ISO 13445 Block Shear Test — Adhesive Shear Strength Test for Rigid Substrates: 

Tensile testing machine    

Minimum tensile capacity ≥ 45 kN, complying with ISO 7500‑1 (verification for static uniaxial testing machines).

Block‑shear fixture

Composed of a specimen‑holding block and a shearing tool.

  • The holding block can contain adherends up to 80 mm × 80 mm × 13 mm.

  • The shearing tool fits adherends up to 30 mm × 30 mm × 13 mm.

  • An adapter plate is available for smaller‑size specimens to guarantee correct positioning and clamping.

ISO 13445 Block Shear Test — Adhesive Shear Strength Tester for Rigid Substrates


Test Specimen Information:

Standard adherend sizes:

  • Metal blocks: 25 mm × 25 mm × 6 mm

  • Glass plates: 75 mm × 75 mm × 13 mm

  • Other materials: 25 mm × 25 mm × 13 mm

(Tolerances: a = 75 ± 1 mm; b = 25 ± 0.2 mm; c = 13 ± 1 mm; d = 12 mm < d ± 0.2 mm < 13 mm; e = 6 mm for metals, 13 mm for others.)


Test Parameters & Stipulations

Crosshead speed1.5 mm/min
Machine loading modeCompression/tension through the shearing fixture; holding block on top
Measured quantityMaximum force sustained by the specimen
Failure classificationISO 10365 (designation of main failure patterns, e.g. AF, CF, SF)
Calculated quantityMaximum shear stress per specimen = Fmax / bond area; average shear strength = mean of replicates
UnitsMegapascals (MPa)
Replicates≥ 5
Mount the shear fixture with the specimen‑holding block positioned on the top of the test machine.

Install specimens so one adherend is clamped by the holding block and the other contacts the shearing tool. Centre the specimen strictly to eliminate bending/torque moments during loading. Secure the specimen with the toggle clamp.


Test Procedures for ISO 13445 Block Shear Test — Adhesive Shear Strength Test for Rigid Substrates:

  1. Mount the fixture in the testing machine with the specimen-holding block on top (Figure 5 side view: pinhole for mounting, specimen, adapter, shearing tool, clamping end, toggle clamp).

  2. Place the assembled specimen so that one adherend is gripped by the holding block and the other is engaged by the shearing tool.

  3. Centre the specimen in the shearing tool so that no turning moment is applied during shearing.

  4. Close the toggle clamp at the rear of the holding block to keep the specimen (or adapter) located against the shearing tool.

  5. Run the test at 1.5 mm/min crosshead speed and record the maximum force.

  6. Examine the failed adherends and designate the failure pattern per ISO 10365.

  7. Repeat for the remaining specimens (≥ 5 in total) and average the results.


Industry Application Fields

Because it needs only two flat-faced rigid pieces and no machining of the bonded joint, ISO 13445 is used wherever rigid materials are bonded structurally:

  • Ceramics and glass — technical ceramics, optical elements, prisms/lenses, glass-to-metal assemblies

  • Magnet mouldings / bonded magnets — electric motors, sensors, loudspeakers, EV drivetrains

  • Rigid plastics and composites — housings, structural plastic parts

  • Metal-to-metal structural bonding — aerospace, automotive, rail, marine, general engineering

  • Electronics and electrical — component/substrate bonding, encapsulation and potting interfaces

  • Adhesive manufacturers and formulators — R&D, formulation ranking, batch QC, product data sheets

  • Surface-treatment and process validation — quantifying the effect of cleaning/priming/abrasion, bondline thickness, cure conditions

  • Failure analysis and quality assurance — verifying production bonds, root-cause work using ISO 10365 failure codes


Related Stadard: 

ISO 4587Adhesives - Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies.
ASTM D1002Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D4501Standard Test Method for Shear Strength of Adhesive Bonds Between Rigid Substrates by the Block-Shear Method; the US counterpart to ISO 13445, using the same block-shear fixture and peak-load ÷ bond-area calculation.
EN 1465Adhesives - Determination of tensile lap-shear strength of bonded assemblies
ISO 13445Adhesives — Determination of shear strength of adhesive bonds between rigid substrates by the block-shear method
ISO 11339Adhesives — T-peel test for flexible-to-flexible bonded assemblies
ASTM D3165

Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies

ASTM D3528Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
ISO 11003-2Structural adhesives — determination of shear behaviour (different geometry/method)
ISO 19210Wood adhesive lap-shear test (specialised for non-rigid wood substrates)
ISO 9664

Adhesives - Test methods for fatigue properties of structural adhesives in tensile shear

ASTM D5656Standard Test Method for Thick-Adherend Metal Lap-Shear Joints for Determination of the Stress-Strain Behavior of Adhesives in Shear by Tension Loading
ASTM D5868

Standard Test Method for Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) Bonding


Why This Test Is Important for Materials

  1. Near-pure shear loading. Thick, rigid adherends barely deform, so the load path stays in the bond plane. The measured strength reflects the adhesive (or the interface), not adherend bending — unlike a lap-shear coupon, where stress concentrates at the overlap ends and peel contaminates the result.

  2. Works on non-machinable materials. Glass, ceramics, sintered magnet mouldings and moulded plastic parts can be tested as-is, with only one flat face required — no slotting, drilling or precision lap geometry.

  3. Comparative, decision-grade data. It ranks adhesives, surface preparations, primers, bondline thicknesses, cure cycles and ageing conditions under identical, standardised conditions — the basis for material selection, process windows and QC release limits.

  4. Failure mode tells you why. Paired with ISO 10365 coding, a low value plus AF (adhesive/interfacial failure) points to a surface-preparation problem, whereas CF (cohesive failure) means the adhesive bulk is the limit; SF/CSF means the substrate failed first.

  5. Feeds structural design and durability assessment. Block-shear strength is a key input for sizing rigid bonded assemblies and for validating bonded joints in safety-relevant sectors (aerospace, automotive, electronics, optics)


Keywords: ISO 13445 block shear tester, adhesive bond shear strength test, rigid substrate adhesive shear test, block-shear method adhesive tester, high modulus substrate adhesive test, industrial adhesive mechanical test, adhesive formulation testing, machinable substrate bond test, non-machinable substrate shear test, adhesive quality inspection tester, UnitedTest adhesive bond testing machine

Related products and device

ISO 13445 Tensile Testing Machine for Rigid Substrates, Block Shear Test — Adhesive Shear Strength Tester

A single column tensile tester is a sophisticated material testing instrument designed for measuring mechanical properties of various materials under tension, compression, bending, shear, and other loading conditions. As the name suggests, it features a single vertical column supporting a moving crosshead that applies force to test specimens.

ISO 13445 Adhesive Shear Strength Tester test fixture

Vice Tensile test fixture for plastics is based on the test standatd ASTM D638, determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, speed.

Related Standard

ASTM D1002 Lap Shear Test of Adhesively Bonded Metal Specimens –

ASTM D1002 is the most widely used standard test for measuring the apparent shear strength of metal‑to‑metal adhesive single‑lap joints under tension loading. It provides comparative data for adhesive selection, process control, and quality assurance in structural bonding applications. It is the most common test for evaluating adhesive shear performance.

ASTM D897 Tensile Test of Adhesive Bonds –

ASTM D897 prescribed a method for determining the comparative tensile properties of adhesive bonds in a standard specimen when tested under specific conditions. Its primary purpose was to measure the tensile strength of an adhesive bond between two rigid substrates (metal to metal). 

ASTM D412 Tensile Strength of Rubber and Elastomers –

ASTM D412 test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers. These methods are not applicable to ebonite and similar hard, low elongation materials. 

ASTM D412 is the primary standard for evaluating the tensile properties of vulcanized thermoset rubbers and thermoplastic elastomers (TPEs). It provides precise procedures for determining critical mechanical characteristics that define material performance under stretching forces. 

The methods appear as follows:

Test Method A—Dumbbell and Straight Section Specimens

Test Method B—Cut Ring Specimens

ISO 812 Low-temperature brittleness Impac Test of Rubber, vulcanized or thermoplastic –

ISO 812:2017 specifies a method for determining the lowest temperature at which rubber materials do not exhibit brittle failure or the temperature at which half of the test pieces used in a test fail when impacted under specified conditions.

The temperatures thus determined do not necessarily relate to the lowest temperature at which the material can be used since the brittleness will be affected by the conditions of test and especially by the rate of impact. Data obtained by this method are, therefore, intended to be used to predict the behaviour of rubbers at low temperatures only in applications in which the conditions of deformation are similar to those specified in the test.


ISO 37 Tensile Test on Rubber, vulcanized or thermoplastic –

ISO 37 and ASTM D412 are both widely recognized tensile test methods designed to evaluate the stress-strain characteristics of various rubber materials, including natural rubber, synthetic rubber, silicone rubber, and thermoplastic elastomers (TPEs). While both standards aim to determine the tensile properties of rubber and elastomers, they differ in their specific methodologies and applications.

ASTM D2137 Rubber Brittleness Point Test of Flexible Polymers and Coated Fabrics –

ASTM D2137: Standard Test Methods for Rubber Property--Brittleness Point of Flexible Polymers and Coated Fabrics


ASTM D2137 test method is used to evaluate the brittleness of rubber materials, or rubber coated fabrics, when exposed to low-temperature flex with an impact under specified conditions of striker speed. ASTM D2137 tests performed will be used to determine the lowest temperature at which rubber compounds will not show fractures or coating cracks when exposed to specified impact conditions.

ISO 4587 Adhesives Tensile Shear Test of rigid bond material –

ISO 4587 Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies

ISO 4587 determining tensile lap-shear strength of adhesive single-lap joints between two rigid substrates, for comparative evaluation rather than structural engineering design data. UnitedTest manufactures high-precision ISO 4587 compliant lap-shear test machines, designed to evaluate the tensile shear performance of rigid-to-rigid adhesive bonded assemblies for industrial quality control and adhesive material comparison. 

Frequently Asked Questions (Q&A) for ISO 13445 Block‑Shear Test

Q1: What is ISO 13445 test used for, and why is it important?

A: ISO 13445 is a block‑shear test standard to measure shear strength of adhesive joints for rigid substrates (ceramic, glass, magnet mouldings, hard plastics, metal) whose elastic modulus is higher than adhesive’s modulus. It minimizes peel‑stress artefacts common in lap‑shear tests, delivering more realistic pure‑shear performance data for thick, hard‑to‑machine parts. It supports adhesive formulation screening, material selection, incoming quality control and joint failure diagnosis for structural bonding applications.


Q2: What is the key difference between ISO 13445 block‑shear and ISO 4587 lap‑shear test?

A: ISO 4587 lap‑shear uses thin overlapping adherends; bending generates unwanted peel stress during loading, which lowers measured strength values. ISO 13445 uses thick block‑shaped adherends, greatly reducing peel effects, better simulating pure‑shear loading. ISO 13445 is preferred for non‑machinable flat substrates such as glass and ceramics, while lap‑shear is more common for thin sheet metal bonding.


Q3: What are the mandatory test parameters in ISO 13445?

A: Test cross‑head speed: 1.5 mm/min

Minimum 5 valid replicate specimens

Machine capacity ≥ 45 kN, compliant with ISO 7500‑1 force verification

Conditioning atmosphere follows ISO 291 standard laboratory conditions

Adhesive bond‑line thickness must be measured to accuracy of 0.02 mm.


Q4: Can I use custom‑sized specimens instead of standard dimensions?

A: Yes, within the fixture capacity limits. However, specimens must be thick enough to avoid substrate deformation. Thin adherends that bend under load are not permitted. Bond faces must maintain parallelism within ± 5 μm/mm; excess squeeze‑out adhesive shall be removed right after assembly. Standard dimensions: metal 25 × 25 × 6 mm; glass 75 × 75 × 13 mm; other rigid blocks 25 × 25 × 13 mm.


Q5: Why must the specimen be perfectly centred in the shearing fixture?

A: Off‑centre mounting introduces turning moment / eccentric load. This creates mixed shear‑peel stress, causes premature failure, and produces invalid, scattered shear‑strength results. The toggle clamp and optional adapter plate are designed to guarantee correct alignment for both large and small block specimens.


Q6: What common mistakes lead to bad ISO 13445 test data?

A: Using too‑thin adherends that deform during shear;

Mis‑aligned / off‑centred specimen generating bending moment;

Ignoring surface‑preparation requirements of EN 13887;

Not removing squeezed‑out excess adhesive;

Wrong cross‑head speed deviating from 1.5 mm/min;

Inaccurate bond‑line thickness measurement.


Q7: What industries typically perform ISO 13445 block‑shear testing?

A: Structural adhesive manufacturers, ceramic & glass bonding, magnet assembly, electronic component packaging, automotive rigid‑part bonding, aerospace material labs, quality‑control laboratories, R&D for high‑modulus substrate bonding.


Q8. Why is it called "block-shear"?

A: Because the specimen is a pair of rigid blocks rather than thin overlapping strips. The geometry forces the load to act essentially in the plane of the bond line, producing a near-pure shear state.


Q9. Can thin or flexible adherends be tested?

A: No. The standard explicitly states the method is not applicable to thin adherends where specimen deformation would occur — deformation would invalidate the assumption of pure shear.


Q10. How is ISO 13445 different from ISO 4587 lap-shear?

A: ISO 4587 uses a single-lap joint of thin rigid strips. Because the two adherends' load paths are offset, the joint bends and the bond experiences peel stress as well as shear, concentrated at the overlap ends — ISO 4587 openly states it does not provide design data. ISO 13445 uses thick rigid blocks so the adherends do not bend, giving a much more uniform, near-pure shear state with minimal peel.


Q11. What other standards are related?

  • ISO 11003-2 — shear behaviour of structural adhesives using thick adherends (gives shear modulus and full stress–strain curve)

  • ASTM D1002, D3163, D3165 — single-lap shear variants (metals, rigid plastics, laminated assemblies)

  • EN 1465 — European tensile lap-shear method

  • ISO 9653 / ASTM D950 / ISO 11343 — shear-impact and wedge-impact methods

  • Supporting: ISO 291 (conditioning), ISO 7500-1 (machine calibration), ISO 10365 (failure patterns), EN 13887 / ISO 17212 (surface preparation)


Q12. Why choose ISO 13445 Block‑Shear Test Machine & Fixture from UnitedTest?

A: UnitedTest supplies complete ISO 13445:2003 block‑shear test solutions, including universal tensile test machines and standardized block‑shear fixtures for measuring adhesive shear strength on glass, ceramic, magnet and rigid plastic substrates. Compliant with EN ISO 13445:2006, ISO 7500‑1.


UnitedTest manufactures professional ISO 13445 block‑shear test machines and dedicated shearing fixtures for adhesive bond shear‑strength measurement following ISO 13445:2003 / EN ISO 13445:2006 standard.

The ISO 13445 block‑shear method evaluates shear performance of adhesives bonded to rigid substrates (glass, ceramics, magnet mouldings, metals and hard plastics). Unlike lap‑shear tests, this block‑shear setup minimizes unwanted peel stress, delivering more accurate pure‑shear data for non‑machinable flat components widely used in electronics, automotive and structural‑bonding industries.


Our ISO 13445 test system includes:

  1. Universal tensile‑compression testing machine with ≥45 kN load capacity, fully compliant with ISO 7500‑1 force‑verification requirements;

  2. Standard ISO 13445 block‑shear fixture: specimen‑holding block, shearing tool, toggle‑clamp assembly, plus interchangeable adapter plate for small‑size block specimens;

  3. Test software supporting calculation of shear stress (MPa), recording peak fracture force, exporting individual‑specimen results and average shear‑strength reports matching ISO 13445 test‑report requirements.

UnitedTest ISO 13445 fixtures can handle standard specimen sizes: metal blocks 25 × 25 × 6 mm, glass plates 75 × 75 × 13 mm and other rigid blocks 25 × 25 × 13 mm. Custom fixture modifications are available for special‑dimension adherends within fixture load limits.


Typical applications:

  • R&D & quality control for structural adhesives

  • Shear‑strength test for ceramic‑to‑metal, glass‑to‑plastic, magnet assembly bonds

  • Material comparison, adhesive batch inspection, bonding‑process validation

  • Lab testing complying with ISO 13445, EN ISO 13445:2006, BS EN ISO 13445:2006.

If you need reliable ISO 13445 block‑shear test equipment for your laboratory, contact UnitedTest for machine quotation, fixture drawing and technical support.

< Previous: ISO 13426-1 Geotextiles Strength of internal structural junctions

> Next: ISO 13468-1 Total light luminous transmittance test of plastic

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.