Home >> Application >> By Standard >> Others >> IEC 60068-2-75 Hammer Test for Enclosure Impact Verification

IEC 60068-2-75 Hammer Test for Enclosure Impact Verification

Share:

IEC 60068-2-75 Test Eh Hammer Test Machine | UnitedTest

UnitedTest manufactures IEC 60068-2-75 hammer test equipment for electrotechnical product mechanical impact testing. It covers three standardized test methods including spring hammer, pendulum hammer and vertical hammer, with adjustable impact energy from 0.14 J to 50 J, used to verify mechanical robustness and support product safety assessment, quality control and type approval.


IEC 60068-2-75 Environmental testing — Part 2-75: Tests — Test Eh: Hammer tests specifies three coordinated hammer impact test methods, namely spring hammer test Ehb, pendulum hammer test Eha and vertical hammer test Ehc, to evaluate whether electrotechnical products can withstand defined mechanical impacts during transportation, installation and daily service. This standard defines impact energy grades, striking geometry, test setup and calibration requirements, widely adopted for safety verification of electrical components, enclosures, control panels and electronic assemblies. UnitedTest’s IEC 60068-2-75 hammer test machine delivers stable, repeatable impact loading, supports flexible energy configuration and meets lab accreditation requirements for environmental mechanical reliability testing.


Core Test Principle

The core principle of Test Eh is to apply a defined number of calibrated mechanical impacts to pre-selected locations on a test specimen, using standardized hammer devices that deliver precise, repeatable impact energy. The test evaluates whether the specimen retains its mechanical integrity, safety performance and functional characteristics after impacts that simulate real-world mechanical stress (e.g., accidental knocks during handling, installation or use, and low-level vandalism).

For any given severity level, the three hammer types are engineered to produce equivalent test results as far as practicable, so test outcomes are not dependent on the choice of test apparatus.


Specific test methods

DesignationMethodEnergy range / typical useSuitable surfaceWorking principleKey apparatus constraints
Test EhaPendulum hammer0.14–50 J; widely used for certification and higher IK levelsVertical surfaces without overhangsRigid pendulum released from a defined height; falls only under gravity; energy = m·g·h, with g taken as 10 m/s²Pivot axis 1 000 mm above the measuring point; hammer retained after first strike to avoid rebound; for ≥2 J the arm-to-striking-element mass ratio ≤0.2 and the striking element’s centre of gravity close to the arm axis; cord/steel-ball variant is not recommended
Test EhbSpring hammer≤2 J (0.14–2 J); portable, any orientationAny position, provided there is room and energy ≤2 JEnergy stored in a calibrated spring; spring fully released ~1 mm before impact, so the last 1 mm is free flight; gravity correction needed when not horizontalStriking-element assembly 250 g (200 g historic) for ≤1 J, 500 g for 2 J; release force ≤10 N; 8–12 mm free overtravel after the impact plane; 2 J release head cylindrical, 23 mm long × Ø35 mm; shall be calibrated
Test EhcVertical hammer0.14–50 J; falling-object / free-fall simulationNormally accessible horizontal surfaces (upward-facing)Striking element falls freely from rest through a height from Table 2 onto a horizontal specimenGuided by 3 or 4 rails with negligible braking; guideway must not rest on the specimen and the striker must be free of the guideway at impact; striker length l ≥ diameter D; ~1 mm gap to reduce friction


Test Specimen Requirements and Stipulations

The specimen is an electrotechnical item — component, equipment, enclosure, cover, switch, lamp holder, etc. — tested in its normal service condition .

It shall be either (a) mounted by its normal means on a rigid plane support or (b) placed against a rigid plane support, as prescribed by the relevant specification .

The relevant specification must state any requirements for securing bases, covers and similar items before impact, and must define the attitude of the specimen and the impact locations — chosen where damage is most likely to occur in practice .

Initial measurements: visual, dimensional and functional checks as prescribed .

Operating mode: the relevant specification states whether the specimen must operate during impact and whether functional monitoring is required; in both cases it must give acceptance/rejection criteria . A safety note warns that if the specimen breaks, internal parts may become hazardous .


Test Equipment of IEC 60068-2-75 Hammer Test for Enclosure Impact Verification

1 Test Eha: Pendulum Hammer

  • Apparatus structure: A rigid pendulum arm rotates in a vertical plane, with its pivot axis positioned 1000 mm above the measuring point of the striking element. The striking element conforms to the coordinated geometric and mass specifications in Table 1 of the standard.

  • Energy-specific variants:

    • For severities ≤ 1 J: The striking element has a steel body with a polyamide hemispherical impact face, with a combined mass of 200 g (a 150 g legacy variant is retained for historical consistency).

    • For severities ≥ 2 J: The mass of the pendulum arm shall not exceed 20% of the combined mass of the striking element, and the centre of gravity of the striking element shall be aligned with the arm axis.

  • Operation: The hammer is released and falls solely under gravitational force. A portable pendulum variant is permitted for large, heavy or hard-to-handle specimens, provided mounting rigidity and impact axis alignment are verified.

  • Fall height: Calibrated fall heights for each energy level are defined in Table 2 of the standard.

2 Test Ehb: Spring Hammer

  • Apparatus structure: Consists of three principal assemblies: the body (housing, striking element guide, and release mechanism), the striking element (hammer head, shaft, and cocking knob), and the release system.

  • Mass specifications: 250 g striking element assembly for energies ≤ 1 J (200 g legacy alternative), and 500 g for 2 J energy level.

  • Key design feature: The hammer spring fully releases all stored energy approximately 1 mm before the hammer head reaches the impact plane. During the final 1 mm of travel before impact, the striking element moves as an unconstrained free mass with only kinetic energy. After passing the impact plane, it can travel a further 8–12 mm without mechanical interference.

  • Gravity correction: When used in non-horizontal orientations, the delivered energy is adjusted by the formula ΔE = 10 × m × d × sinα to account for gravitational influence on the striking element.

  • Calibration: Mandatory calibration per normative Annex B, using a pendulum-based reference calibration device to verify actual delivered impact energy.

  • Key advantage: Operable in any spatial orientation, but limited to a maximum energy of 2 J for operational safety and practicality.

3 Test Ehc: Vertical Hammer

  • Apparatus structure: A guided striking element falls freely from rest through a specified vertical height onto a horizontally oriented specimen surface. The element travels along a low-friction guideway (e.g. 3 or 4 parallel rails).

  • Design requirements:

    • The length of the striking element shall be no less than its diameter.

    • A small clearance (~1 mm) between the element and guideway minimizes braking friction.

    • The guideway does not rest on the specimen, and the striking element is free of the guideway at the moment of impact.

  • Fall height: Uses the same height values as Table 2, where the equivalent mass equals the actual mass of the striking element.


Test Parameters

Standard impact energy levels0.14, 0.2, (0.3), 0.35, (0.4), 0.5, 0.7, 1, 2, 5, 10, 20, 50 J(Values in brackets are legacy values retained for historical consistency, no longer recommended)
Energy tolerance±10% for energies ≤ 1 J; ±5% for energies ≥ 2 J
Number of impacts3 impacts per test location (default, unless otherwise specified)
Striking element materialPolyamide (85–100 sHRR, ISO 2039-2) for ≤ 1 J;Carbon steel Fe 490-2 (HRE 80–85, ISO 6508) for ≥ 2 J
Equivalent mass (±2% tolerance)0.25 kg (≤ 1 J, 0.2 kg legacy); 0.5 kg (2 J); 1.7 kg (5 J); 5 kg (10 J, 20 J); 10 kg (50 J)
Mounting rigidity requirementSupport surface displacement ≤ 0.1 mm when struck at the test energy level; a mounting mass ≥ 20× the specimen mass is generally deemed sufficiently rigid


Test Procedures of IEC 60068-2-75 Hammer Test for Enclosure Impact Verification

  1. Pre-test inspection: Perform initial visual, dimensional and functional checks on the specimen.

  2. Specimen mounting: Secure the specimen in the specified attitude on the rigid support, and verify mounting rigidity meets requirements.

  3. Apparatus preparation: Calibrate the hammer device, set the target impact energy (via fall height for pendulum/vertical hammers, or spring adjustment for spring hammers), and inspect the striking face for damage.

  4. Impact execution: Apply 3 impacts to each designated test location, perpendicular to the surface. Restrain the hammer after each strike to prevent rebound.

  5. In-test monitoring: Conduct continuous or periodic functional monitoring if required.

  6. Recovery phase: Allow the specified recovery period if applicable.

  7. Post-test evaluation: Perform final measurements and assess compliance against the defined acceptance/rejection criteria.


Industrial Application Fields

  • Primary sector: Electrical and electronic industry, including low-voltage switchgear, control devices, building electrical accessories, lamp holders, household appliances, electrical enclosures, connectors and IT equipment.

  • Extended use: Automotive electronics, industrial control equipment, consumer electronics and any product where impact robustness is a safety or reliability requirement.

  • The test is particularly relevant for equipment installed in publicly accessible areas (exposed to accidental impacts or minor vandalism) and for products with brittle housing materials.


Related Standard: 

IEC 60068‑2‑75Normative reference, defines hammer‑test hardware and operation methods (Test Eh) used to perform IEC 62262 impact tests
IEC 62262
Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
IEC 60529IP‑code standard for ingress protection (dust/water). IEC 62262 complements it for mechanical‑impact resistance; IEC 62262 pass criteria require preservation of IP‑code performance.
EN 50102Original CENELEC European standard, the foundational source document for IEC 62262


Keywords: IEC 60068-2-75, Test Eh hammer test, impact hammer tester, spring hammer test machine, pendulum hammer impact tester, vertical hammer test equipment, electrotechnical product impact test, mechanical robustness test, environmental impact test, 0.14J to 50J impact test, electrical enclosure impact test, IEC 60068 impact testing, safety assessment impact test, reliability hammer test, lab impact test apparatus, UnitedTest hammer tester, electronic product impact resistance test, IK impact test, mechanical shock test instrument, product qualification impact test

Related products and device

IEC 60068-2-75 IK Protection Degree Impact Testing Machine (IK Vertical Impact Tester)

UnitedTest manufactures IK vertical impact testing machine complying with IEC 62262, IEC 60068-2-75 Test Ehc vertical hammer. For IK rating test, IK01-IK10 enclosure mechanical impact resistance test, with standard fixtures, calibration, lab & certification testing. Get IK vertical drop hammer impact tester details.

tensile testing machine for paper

A single column tensile tester is a sophisticated material testing instrument designed for measuring mechanical properties of various materials under tension, compression, bending, shear, and other loading conditions. As the name suggests, it features a single vertical column supporting a moving crosshead that applies force to test specimens.

Related Standard

IEC 62262 IK Impact Test for IK Code Enclosure Testing –

IEC 62262 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)

IEC 62262 defines a classification system (IK code) for the degree of protection that an enclosure of electrical equipment provides against external mechanical impacts, for equipment with a rated voltage ≤ 72.5 kV. It applies only where the relevant product standard actually calls up impact degrees of protection.


EN 477 Falling Mass Impact Test for PVC Profiles –

EN 477 Plastics‑Poly(vinyl chloride) (PVC)‑based profiles‑Determination of the resistance to impact of profiles by falling mass

EN 477 specifies a drop‑weight impact test for rigid unplasticized PVC‑U profiles, primarily performed at −10 °C, and can also apply for other defined test temperatures for PVC‑based profiles.


ASTM D3029 Impact Resistance of Flat Rigid Plastic By Falling Tup Weight –

ASTMD3029 is designed to determine the relative ranking of rigid plastic materials based on the energy required to crack or break them under specified impact conditions.

ASTM D5420 Gardner falling weight impact test for flat rigid plastic –

ASTMD5420 measures the relative ranking of materials based on the energy required to crack or break a plastic sheet when struck by a falling weight (the "Gardner Impact" method).



ASTM D5628 Falling Tup Impact Resistance Test of Rigid Plastics –

ASTMD5628 specifies a falling‑dart/tup method to measure the threshold impact‑failure energy for flat rigid plastics. It uses the Bruceton Staircase (Up‑and‑Down) Method to determine the energy causing 50% of specimens to fail (mean‑failure energy, MFE).

ISO 6603-1 Rigid plastics falling dart puncture-impact test –

ISO 6603-1 specifies falling-dart methods to measure the puncture‑impact performance of rigid plastics using only the 50% impact‑failure energy (E₅₀) threshold, without recording force–time or force–deflection curves.

ISO 11173 Plastic pipe falling weight impact test –

ISO 11173 specifies the staircase falling-weight impact method to evaluate the external impact resistance of circular thermoplastic pipes, mainly for batch qualification at 0 °C (–20 °C recommended for sub-zero testing).

EN 744 for falling weight impact testing of thermoplastics pipes –

EN 744 specifying the round-the-clock falling-weight impact method to evaluate the resistance to external blows of circular cross-section thermoplastics pipes. It's a standardized procedure to determine the ability of thermoplastic pipes to withstand external impacts without failing.


Frequently Asked Questions (FAQs) – IEC 60068-2-75 Test Eh: Hammer Tests

Q1. What is IEC 60068-2-75 Test Eh?

It is the IEC basic safety publication Environmental testing — Part 2-75: Tests — Test Eh: Hammer tests (Edition 2.0, 2014-09). It defines three coordinated hammer methods for applying a prescribed number of defined-energy impacts to an electrotechnical specimen, in prescribed directions, to demonstrate an acceptable level of robustness during product safety assessment. It covers 0.14 J to 50 J.


Q2. Why is the hammer test important?

Because a single knock can turn a compliant product into a safety hazard. A cracked enclosure may expose live parts, reduce creepage/clearance, destroy IP ingress protection, detach a cover, or disable a protective function. The test converts "it feels solid" into a repeatable, quantified joule value applied at real weak points, and it is referenced by product safety standards such as IEC 60335-1, IEC 60598-1 and IEC 61010-1. It protects users, supports certification, and gives R&D a measurable design limit.


Q3. What do Eha, Ehb and Ehc mean?

They are the three apparatus-specific methods:

  • Eha — Pendulum hammer: gravity-driven swing, 0.14–50 J, for vertical surfaces without overhangs.

  • Ehb — Spring hammer: calibrated spring, ≤2 J, usable in any orientation.

  • Ehc — Vertical hammer: guided free fall, 0.14–50 J, for accessible horizontal surfaces.


Q4. Which impact energies are standardized?

0.14, 0.2, 0.35, 0.5, 0.7, 1, 2, 5, 10, 20 and 50 J. The values 0.3 J and 0.4 J appear in brackets as historic alternatives from earlier IEC 60068-2 parts; they are no longer recommended but may be used for historical comparison.


Q5. How many blows are applied?

Unless the relevant product specification says otherwise, three impacts per location. Severity = chosen energy + number of impacts.


Q6. How do I choose the right hammer?

By surface orientation, energy level, and whether the specimen can be moved:

Vertical face, no overhang, any energy up to 50 JEha pendulum
Any orientation, ≤2 J, portable/field useEhb spring hammer
Horizontal upward-facing surface, falling-object simulationEhc vertical hammer


Q7. What is the relationship between IEC 60068-2-75 and the IK code?

IEC 62262 defines the IK classification (IK00–IK10; Amendment 1:2021 added IK11 at 50 J) and the classification/acceptance conditions. It uses the hammer apparatus and impact procedure of IEC 60068-2-75 to deliver the energy. In short: IEC 60068-2-75 = how to hit; IEC 62262 = what level you claim. The European equivalent is EN 62262 (which superseded EN 50102); the Chinese equivalent is GB/T 20138.


Q8. Is IK the same as IP?

No. IEC 60529 defines the IP code for protection against access to hazardous parts, solid objects and water; it explicitly excludes mechanical impact. IK covers external mechanical impact. A product is normally described by both, e.g. IP65 / IK08. Impact testing is often used to verify that the IP rating is still valid after the blow.


Q9. What are "equivalent mass" and "measuring point"?

Equivalent mass is the mass of the striking element plus the relevant moving parts of the apparatus which, combined with its velocity, delivers the impact energy. For a pendulum with an evenly distributed arm it equals the combined striker mass plus half the arm mass. The measuring point is a defined point on the striker surface used to measure the height of fall — the vertical distance from release to moment of impact.


Q10. What exactly is the specimen, and how is it mounted?

The specimen is the assembled electrotechnical item (enclosure, cover, switch, luminaire, lamp holder, junction box, panel, etc.), normally in its service condition. It is either mounted by its normal means on a rigid plane support or placed against one. A typical support is brick/concrete covered by a tightly fixed ~8 mm polyamide sheet, HRR 85–100, with no air gap. Rigidity criterion: support displacement ≤0.1 mm under a direct blow of the same energy; a mounting mass ≥20× the specimen mass is likely sufficient.


Q11. Is this a raw-material test like Charpy or Izod?

No. Charpy (ISO 148 / ASTM E23), Izod (ISO 180 / ASTM D256) and instrumented puncture tests measure notched or unnotched material coupons. IEC 60068-2-75 tests the finished product: geometry, wall thickness, corners, weld lines, snap-fits, inserts, assembly and material together. A resin with a good datasheet Izod value can still fail in a real housing.


Q12. Why is material selection still critical?

Because the blow lands on stress concentrators — corners, seams, bosses, windows, thin walls, weld lines. Brittle materials (glass, ceramics, unmodified plastics) crack; ductile metals and impact-modified polymers deform. Annex C singles out equipment of a brittle nature as especially appropriate for this test, and Annex C.4 warns that specimen temperature may influence results — a polymer that passes at room temperature may fail after cold exposure or UV/thermal ageing.


Q13. Why must rebound / secondary impacts be avoided?

A second, uncontrolled strike adds unquantified energy and invalidates the severity. The standard requires rebounds to be avoided; for Eha the operator grasps the striking element after the first impact without distorting the arm, and for Ehb the release mechanism is used so the striker has 8–12 mm of free overtravel after the impact plane.


Q14. Which parameters must be controlled for repeatable results?

Energy tolerance (±10 % for ≤1 J, ±5 % for 2–50 J), equivalent mass ±2 %, height of fall ±1 %, striker geometry per Table 1 (R, D, f, r, l), striker material/hardness (polyamide 85–100 HRR for ≤1 J; Fe 490-2 steel for ≥2 J), perpendicular blows, visual inspection of the striking face before every impact, rigid mounting, and g = 10 m/s² for energy calculation.


Q15. Which industries and products use it?

Household appliances, luminaires and streetlights, switches/socket-outlets/lamp holders, low-voltage switchgear and industrial control panels, IT/telecom cabinets, EV charging stations, rail and traffic equipment, security/CCTV, medical and laboratory equipment, automotive, aerospace avionics, and military/defense enclosures — essentially any enclosure in a non-restricted-access area where knocks, tool drops or vandalism are plausible.


Q16. How does it differ from IEC 60068-2-27 shock or IEC 60068-2-31 rough handling?

IEC 60068-2-27 (Test Ea) applies specified shock pulses on a shock machine; IEC 60068-2-31 (Test Ec) covers drop, topple and repeated free fall of equipment-type specimens. Test Eh is a localized, defined-energy hammer blow on a mounted enclosure surface, not a whole-product acceleration pulse or a drop onto a floor. They answer different questions and are often used together in a test sequence.


Q17. Why choose IEC 60068-2-75 Hammer Test Machine | Pendulum & Spring Hammer Tester from UnitedTest? 
UnitedTest manufactures IEC 60068-2-75 compliant hammer test equipment, including pendulum, spring and vertical hammer testers for Test Eh impact testing of electrical products. Full energy range 0.14 J – 50 J.


UnitedTest is a professional manufacturer of high-precision environmental testing machines, specializing in IEC 60068-2-75 compliant hammer test apparatus for electrotechnical product safety and reliability verification. Our complete Test Eh hammer test line includes pendulum hammer testers (Test Eha), spring hammer testers (Test Ehb) and vertical hammer testers (Test Ehc), all engineered to strictly meet the requirements of IEC 60068-2-75:2014 Edition 2.0, delivering accurate, repeatable and laboratory-grade impact test results.

Our IEC 60068-2-75 hammer test machines cover the full standard energy range from 0.14 J to 50 J, with interchangeable striking elements manufactured to the exact geometric, material and hardness specifications defined in the standard (polyamide heads for ≤ 1 J, hardened steel heads for ≥ 2 J). Each unit is factory-calibrated and comes with full traceable documentation to support third-party laboratory accreditation, CB certification, CE marking and ISO quality system audits.

Core Product Range

  • Pendulum Hammer Tester (Test Eha): Fixed bench-top and portable models available, with precision fall height adjustment and rigid pivot design. Ideal for testing electrical enclosures, wall switches, lamp holders and household appliance housings at energies from 0.14 J up to 50 J.

  • Spring Hammer Tester (Test Ehb): Lightweight handheld design with adjustable spring compression, suitable for on-site testing and hard-to-reach surfaces. Calibrated for 0.14 J to 2 J energy levels with built-in gravity correction guidance for angled use.

  • Vertical Hammer Tester (Test Ehc): Low-friction guide rail structure with controlled free-fall release mechanism, designed for horizontal surface impact testing in full compliance with IEC 60068-2-75 Test Ehc.

All systems are supplied with a full set of mounting fixtures and specimen adapters for common test sample types, and are compatible with the standard’s rigid backing and mounting rigidity requirements. UnitedTest also offers optional calibration kits, spare parts and annual on-site calibration services to ensure long-term test accuracy and regulatory compliance.


UnitedTest serves electrical appliance manufacturers, third-party testing laboratories, quality inspection institutions and R&D centers worldwide, providing reliable, cost-effective IEC 60068-2-75 hammer test solutions tailored to different industry needs and budget requirements.

< Previous: EN 1447 long-term internal pressure test for GRP, GRE and fiberglass pipes

> Next: EN 12201-2 Guide for PE Pipe Testing Methods and Testing Equipment

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.