Home >> Application >> By Standard >> ISO >> ISO 5000~9999 >> ISO 7743 rubber compression test for stress and strain with parallel platens

ISO 7743 rubber compression test for stress and strain with parallel platens

Share:

ISO 7743 Rubber Compression Stress-Strain Tester | UnitedTest

UnitedTest manufactures ISO 7743 compression test machines for vulcanized rubber and thermoplastic rubber. Measure compression modulus, stress-strain curve for rubber mounts, O-rings, seals and elastomer components for R&D and quality control.


ISO 7743 defines standardized laboratory methods to determine the compression stress-strain properties of vulcanized or thermoplastic rubber elastomers. It supports four distinct test procedures covering lubricated platens, bonded assemblies, dedicated specimen types and direct testing on finished components or cut product segments, delivering reliable compression modulus, stress and strain data for material characterization. This test is widely used for anti-vibration mounts, bridge bearings, sealing rings, O-rings and rubber gaskets, helping engineers evaluate stiffness, load-bearing performance and detect internal porosity. Our UnitedTest compression stress-strain testing machine strictly follows ISO 7743 requirements, features parallel compression platens, controlled test speed and accurate load and displacement acquisition, suitable for incoming inspection, product formulation development, batch quality verification and third-party laboratory certification.


Test Principle: 

A test piece (either lubricated against or bonded to compression plates) is compressed at a constant traverse speed between parallel platens until a specified strain is reached. The force-deformation curve is recorded to calculate compression modulus, stiffness, and other stress-strain characteristics.

Interface conditions (lubrication vs. bonding) and specimen geometry determine whether compression is uniaxial or biaxial:

  • Full slip (lubricated) produces near-uniaxial compression, with results dominated by material modulus.

  • Bonded or high-friction interfaces constrain radial expansion, creating biaxial stress and making results shape-dependent.


Specific Test Methods

MethodTest SpecimenInterface ConditionCore CharacteristicPrimary Use
Method AStandard test piece ALubricated polished metal platesResults depend only on rubber modulus (shape-independent if full slip is achieved)General material comparison
Method BStandard test piece ARubber bonded to metal platesStrong shape dependence; results reflect both modulus and specimen geometrySimulation of bonded component behaviour
Method CStandard test piece BOptional lubricationResults independent of both shape and friction; measures true intrinsic material propertiesFundamental material characterization
Method DFinished product / product partLubricated platens (no lubrication for products with bonded rigid parts)Shape-dependent results, comparative in natureQuality control of finished goods (O-rings, profiles, mounts)

All methods A, B, C use 25% peak strain; method D uses 30% peak strain with properties reported at 25% strain.


Key Parameters and Stipulations

  • Test speed: (10 ± 2) mm/min constant crosshead speed.

  • Strain targets:

    • Methods A/B/C: 0–25% cyclic strain; modulus reported at 10% and 20% strain.

    • Method D: 0–30% single compression; stiffness reported at 25% strain.


Test Specimen Information:

Standard test piece ACylinder: diameter (29 ± 0.5) mm, height (12.5 ± 0.5) mm. Used for Methods A and B.
Standard test piece BCylinder: diameter (17.8 ± 0.15) mm, height (25 ± 0.25) mm. Used for Method C.
Method B bondingTest pieces may be directly moulded to metal plates using a suitable mould/bonding system, or adhered using suitable non-solvent adhesive systems.
Method D product pieces

A product, a part of a product, or multiples thereof. For profiles, use a 50 mm to 100 mm length, or two such lengths together if needed to increase force.

For ring-shaped products with inner diameter 50 mm to 100 mm, use the whole product. Small products may be tested side by side, parallel to each other.

Number of test piecesAt least three test pieces, or sets of test pieces.


ISO 7743 rubber compression test for stress and strain with parallel platens required Testing Equipment: 

Universal Test Machine
  • Complies with ISO 5893, operating at a constant speed of (10 ± 2) mm/min.

  • Displacement accuracy: ±0.02 mm for standard specimens;

  • Equipped with x-y force-deformation recording 

Compression platens

For methods A/D: Highly polished surface (Ra ≤ 0.4 μm per ISO 4287); lateral dimensions at least 20 mm larger than the specimen.

For method B: Surfaces prepared for adhesive bonding.

For method C: No special surface preparation required.


Key Test Procedures of ISO 7743 rubber compression test for stress and strain with parallel platens:

Methods A, B & C

  1. Prepare the interface: apply lubricant (A), use bonded assembly (B), or use bare specimen with optional lubrication (C).

  2. Center the specimen between the compression platens.

  3. Perform four uninterrupted compression-release cycles from 0% to 25% strain at 10 mm/min.

  4. Record the full force-deformation curve.

  5. Calculate compression secant modulus from the compression phase of the fourth (final) cycle, at 10% and 20% strain.


Method D (Product Testing)

  1. Center the product on the lubricated lower platen; use vented platens for rings.

  2. Compress once to 30% strain at 10 mm/min (pre-conditioning cycles are optional and must be reported if used).

  3. Record the force-deformation curve.

  4. Read force at 25% strain and calculate stiffness S25 (in N or N/m).


Result Expression

  • Methods A/B/C: Compression secant modulus in MPa, reported as the median of individual specimen values at 10% and 20% strain.

  • Method D: Stiffness at 25% compression S25 in newtons or newtons per metre, reported as median.


Industries application:

The Introduction of ISO 7743 highlights several direct applications:

  • Civil/structural engineering: bridge bearings, bearing pads, base-isolation and load-bearing rubber components.

  • Automotive, rail, aerospace and industrial machinery: anti-vibration mountings, engine mounts, bushings, bumpers, pads and vibration isolators.

  • Sealing technology: O-rings, pipe sealing rings, gaskets and profiles.

  • Quality control of small/thin products: especially small O-rings and products under 2 mm thick, where hardness cannot easily be measured.

  • Defect detection: compression tests can reveal porosity in products such as pipe sealing rings.

  • Rubber compound development and batch release: comparing compound stiffness, checking batch-to-batch consistency, and supporting incoming/outgoing inspection.

  • Material modelling and FEA: deriving secant/compression modulus or, with Annex B corrections, an estimate of Young’s modulus for design calculations.

  • Product comparative testing: Method D provides a stiffness value for real products or parts where a standard test piece is not representative.

For well-specified shapes such as O-rings, the compression result can be correlated to hardness, which makes the test useful where conventional hardness testing is impractical.

ISO 7743 rubber compression test for stress and strain with parallel platens


Related Test Standard

ASTM D695Standard Test Method for Compressive Properties of Rigid Plastics
ISO/TR 9272 / ISO 19983     Rubber test method precision evaluation frameworks (used for the precision data in Annex D).
ASTM D3410Shear‑loading compression test for polymer‑matrix composites with unsupported gauge section, suited for high‑strength continuous‑fiber composite laminates (not pure end‑loading as D695).
ASTM D575

Standard Test Methods for Rubber Properties in Compression.

ISO 7616Cellular plastics, rigid-Determination of compressive creep under specified load and temperature conditions
ISO 844Rigid cellular plastics — Determination of compression properties
ISO 4666-3

Rubber, vulcanized — Determination of temperature rise and resistance to fatigue in flexometer testing — Part 3: Compression flexometer (constant-strain type)

ISO 3384

Compression stress relaxation; a time-dependent property, distinct from ISO 7743

ISO 604Plastics -- Determination of compressive properties 
ISO 7743Rubber, vulcanized or thermoplastic; determination of compression stress-strain properties
GB/T 7757Chinese standard Rubber, vulcanized or thermoplastic — Determination of compression stress-strain properties.
JIS K 6254Japanese standard for compression and tensile stress–strain properties. It is MOD relative to ISO 7743
ISO 815-1Compression set at ambient or elevated temperatures . It measures permanent deformation after prolonged compression, not short-term stress–strain behaviour.
ISO 5893Specification for tensile, flexural and compression test equipment of constant rate of traverse
TCVN 11993Plastics. Determination of compressive properties


Why This Test Matters for a Material

  1. Engineering design foundation: Compression stress-strain data is essential for dimensioning load-bearing rubber components that must support static and dynamic loads while maintaining function.

  2. Intrinsic vs. product-level characterization: Method C isolates true material modulus, while method D measures real-world product stiffness, bridging material science and component performance.

  3. Quality control for hard-to-test parts: For thin or micro-sized rubber products where shore hardness cannot be reliably measured, compression testing provides a traceable quality metric.

  4. Defect detection: Non-uniform force-deformation behaviour reveals internal porosity in moulded sealing parts, which would cause leakage or premature failure.

  5. Standardized comparability: The four methods provide a globally harmonized framework for comparing materials, products, and supplier performance across laboratories.

  6. Lifetime prediction: Stress-strain data supports modelling of long-term compression behaviour, friction effects, and biaxial stress states, critical for durability and reliability assessment in service.


Keywords: ISO 7743 compression stress-strain tester, rubber compression modulus test machine, vulcanized rubber compression tester, thermoplastic elastomer compression test, elastomer stress strain equipment, rubber mount compression test, O-ring compression testing, rubber seal mechanical property tester, compression platen test rig, rubber material quality control, elastomer R&D test machine, UnitedTest compression tester, rubber static compression test, ISO 7743:2017 tester, gasket compression stress test

Related products and device

ISO 7743 Rubber Compression Universal Testing Machine

WDW Series Computer Control Electronic Universal Testing Machine made by UNITEDTEST range from 100N to 600KN load capacity with various models like single columns, table type, door frame type etc., is used to perform tension, compression, flexure/bending, shearing, peeling etc., test for metal and nonmetal specimens.

ISO 7743 compression test platen

Compression test fixture is used to investigate the compressive behaviour of the test specimens and for determining the compressive strength, compressive modulus and other aspects of the compressive stress/strain relationship under the conditions defined.

Related Standard

ASTM D695 Plastic & composites Compressive Testing –

ASTM D695: Standard Test Method for Compressive Properties of Rigid Plastics

ASTM D695 test covers the determination of the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading. Test specimens of standard shape are employed. This procedure is applicable for a composite modulus up to and including 41,370 MPa (6,000,000 psi). It is technically equivalent to ISO 604 Plastics‑Determination of Compressive Properties. This test applies end‑loading compression on standard‑geometry specimens under controlled environmental and displacement‑rate conditions, delivering compressive strength, yield strength, offset yield strength, compressive elastic modulus, and compressive deformation data.


ASTM D2412 Plastic Pipe Deflection Testing by Compression Loading Test –

ASTM D2412: Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

ASTM D2412 test method covers the determination of load-deflection characteristics of plastic pipe under parallel-plate loading. It covers thermoplastic resin pipe, reinforced thermosetting resin pipe (RTRP), and reinforced polymer mortar pipe (RPMP). Pipes tested under ASTM D2412 must be smaller than the envelope of the two compression platens by at least a half an inch. Square or circular platens can be used, with most customers choosing a square platen. Care must be taken to account for the mid-section of the pipe which will expand slightly as the pipe is compressed.

The characteristics determined by ASTM D2412 test method are pipe stiffness, stiffness factor, and load at specific deflections.

ASTM D3410 Shear Loading compression Test for Polymer Matrix Composite Materials with Unsupported Gage Section –

ASTM D3410 Shear Loading compression Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section. 

ASTM D3410 measuring in‑plane compressive properties for high‑modulus‑fiber‑reinforced polymer‑matrix composites using pure shear‑loading via wedge grips, with an unsupported gage section on the test coupon. Test method determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers. It is applicable to composites made from unidirectional tape, wet-tow placement, textile (for example, fabric), short fibers, or similar product forms. Some product forms may require deviations from the test method.

ISO 14126 In-Plane Compressive Test of Fiber-Reinforced Material –

ISO 14126 Compression test Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction

ISO 14126 specifies how to determine in‑plane compressive properties (i.e. load applied parallel to the plane of lamination, in directions "1" and "2") of fibre‑reinforced plastic composites with thermosetting or thermoplastic matrices. Specimens are machined from a flat test plate or from finished/semi‑finished products.

ISO 604 Compressive Strength Testing of Plastics –

ISO 604 specifies a method for determining the compressive properties of plastics under defined conditions. It is used to investigate the compressive behavior of test specimens and to determine key mechanical properties such as compressive strength, compressive modulus, and other aspects of the compressive stress/strain relationship. Specimen length is adjusted to avoid buckling that would distort results. 

ASTM D575 Rubber Compression Test Method –

ASTM D575 Standard Test Methods for Rubber Properties in Compression

ASTM D575 defines two laboratory test procedures to characterize the compression‑deflection behavior of solid rubber compounds. It does not apply to hard rubber or sponge rubber materials. It contains two inverse procedures: Method A fixes the deflection and measures the force; Method B fixes the force and measures the deflection.


Frequently Asked Questions about ISO 7743 rubber compression test for stress and strain

Q1: What is ISO 7743?

A: ISO 7743:2017 is an international standard that specifies four test methods for determining the compression stress-strain properties of vulcanized or thermoplastic rubber. It covers testing on both standard laboratory specimens and finished rubber products, and is published by ISO/TC 45/SC 2 (Rubber and rubber products – Testing and analysis).


Q2: Why is the ISO 7743 compression test important for rubber materials?

A: The test is critical for several reasons:

  • It provides fundamental engineering data required to design load-bearing rubber components such as bridge bearings, anti-vibration mounts, and seals.

  • It enables quality control on thin or small rubber parts where durometer hardness testing is impractical.

  • It helps detect internal porosity in moulded sealing products that could cause leakage.

  • It delivers standardized, comparable data across laboratories and suppliers worldwide.


Q3: What are the four test methods in ISO 7743, and when should each be used?

A:

  • Method A – Standard disc specimen with lubricated plates. Used for general material comparison when near-uniaxial compression is desired.

  • Method B – Standard disc specimen bonded to metal plates. Used to simulate real-world bonded component behaviour (e.g., engine mounts).

  • Method C – Taller cylindrical specimen (l/d > 1). Used for measuring true intrinsic material properties independent of friction and shape effects.

  • Method D – Finished product or product section. Used for quality control of O-rings, profiles, gaskets, and manufactured parts


Q4: What is the difference between Method A and Method C?

A: The key difference is specimen geometry and friction independence. Method A uses a flat disc (29 mm diameter × 12.5 mm height, l/d ≈ 0.43) and relies on lubrication to achieve uniaxial stress. Method C uses a taller cylinder (17.8 mm diameter × 25 mm height, l/d ≈ 1.4) whose slenderness ratio ensures uniaxial compression regardless of interface friction, making it the most reliable method for measuring intrinsic material modulus.


Q5: What type of test machine is required for ISO 7743?

A: A constant-rate-of-traverse compression testing machine conforming to ISO 5893 is required. The machine must operate at 10 ± 2 mm/min, have Grade 1 force accuracy, displacement resolution of at least ±0.02 mm for standard specimens, and be equipped with x-y force-deformation recording capability.


Q6: What are the standard specimen dimensions?

A:

  • Test piece A (Methods A & B): Cylinder, 29 ± 0.5 mm diameter × 12.5 ± 0.5 mm height.

  • Test piece B (Method C): Cylinder, 17.8 ± 0.15 mm diameter × 25 ± 0.25 mm height.

  • Product specimens (Method D): Full product or 50–100 mm length of profile; full ring for ring-shaped products with 50–100 mm inner diameter.


Q7: Why are four compression cycles performed in Methods A, B, and C?

A: Four uninterrupted compression-release cycles are performed to condition the material mechanically and obtain a stable, repeatable force-deformation curve. Rubber exhibits stress softening (Mullins effect) on initial loading; using the fourth cycle ensures consistent, representative results. Compression modulus is always calculated from the compression phase of the final cycle.


Q8: At what strain levels are results reported?

A:

  • For Methods A, B, and C: Compression secant modulus is reported at 10% and 20% strain, in megapascals (MPa).

  • For Method D: Stiffness at 25% compression (S₂₅) is reported, in newtons (N) or newtons per metre (N/m).


Q9: How does ISO 7743 relate to ASTM D575?

A: Both standards measure rubber compression stress-strain properties and share similar objectives. ISO 7743 specifies four distinct methods with defined cylindrical geometries, while ASTM D575 is the corresponding US standard with comparable but not identical specimen dimensions and procedural details. Results between the two are not directly interchangeable without correlation data.


Q10. Can ISO 7743 test real products such as O-rings?

A: Yes — use Method D. For profiles, a 50 mm to 100 mm length is normally used. For ring-shaped products with an inner diameter of 50 mm to 100 mm, the whole product is used. Small products may be tested side by side in parallel to increase the force reading. Ring testing requires holes in the platens to let air escape. Products with bonded-on rigid components, such as engine mounts, are tested without lubricated platens.


Q11. Why choose ISO 7743 rubber compression test setup with parallel platens and cylindrical test piece from UnitedTest? 

A: UnitedTest manufactures high-precision ISO 7743 compression test machines for vulcanized and thermoplastic rubber. Compliant with ISO 5893, supporting Methods A, B, C and D for compression modulus and stiffness measurement.


UnitedTest is a leading manufacturer of precision compression testing equipment designed specifically for compliance with ISO 7743:2017 – the international standard for determining compression stress-strain properties of vulcanized and thermoplastic rubber.

Our ISO 7743 test machines are engineered to meet the full requirements of ISO 5893 Grade 1 accuracy, delivering reliable compression modulus and stiffness data across all four standard test methods (A, B, C and D). Whether you are testing standard cylindrical specimens in R&D laboratories or performing quality control on finished O-rings, profiles, and anti-vibration mounts on the production floor, UnitedTest provides a tailored testing solution.

Key Features of UnitedTest ISO 7743 Compression Testers

  • Full compliance with ISO 7743 and ISO 5893 – constant traverse speed of 10 ± 2 mm/min with Grade 1 force measurement accuracy

  • High-resolution displacement measurement – ±0.02 mm accuracy for standard specimens, with automatic machine stiffness compensation

  • All four test methods supported – Method A (lubricated disc), Method B (bonded disc), Method C (tall cylinder), and Method D (product testing)

  • Integrated x-y force-deformation data acquisition – real-time curve recording and automatic modulus calculation at 10% and 20% strain

  • Temperature chamber compatibility – testing from –75 °C to 250 °C for full material characterization

  • Polished compression platens – Ra ≤ 0.4 μm surface finish for reliable lubricated testing

  • Safety enclosure – protects operators from specimen ejection during lubricated compression testing

  • Automated cyclic testing – programmable four-cycle conditioning with automatic fourth-cycle data extraction

Applications

UnitedTest ISO 7743 compression testing systems serve rubber manufacturers, automotive component suppliers, sealing product producers, civil engineering bearing manufacturers, and independent material testing laboratories worldwide. Our machines enable accurate measurement of:

  • Compression secant modulus at 10% and 20% strain

  • Stiffness at 25% compression (S₂₅) for finished products

  • Stress-strain curves for material modelling and FEA input

  • Comparative quality control data for production batch release

Why Choose UnitedTest for Your ISO 7743 Testing Needs?

With deep expertise in rubber and polymer testing instrumentation, UnitedTest delivers robust, easy-to-operate systems backed by comprehensive calibration support aligned with ISO 18899. Every machine comes with full documentation, test method presets, and after-sales service to ensure long-term accuracy and regulatory compliance.

< Previous: ISO 7686 Opacity Testing for Plastics pipes and fittings

> Next: ISO 7765-1 Impact resistance by the free-falling dart method

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.