Home >> News >> Blog >> Manual vs. Automatic Melt Flow Index Testers

Manual vs. Automatic Melt Flow Index Testers

Nov. 18, 2026

Share:

Melt flow index testers, also called melt flow indexers or extrusion plastometers, are widely used to evaluate the flow behavior of thermoplastic materials under specified temperature and load conditions. The test produces a Melt Mass-Flow Rate (MFR) and, when applicable, a Melt Volume-Flow Rate (MVR), providing a practical way to compare polymer grades, monitor material consistency, and support quality control.


The main difference between manual and automatic melt flow index testers is not the basic testing principle, but how much of the testing process is controlled or assisted by the instrument. For laboratories testing different thermoplastics, a suitable balance of manual operation and automation can improve efficiency without making the equipment unnecessarily complicated.


image.png


What Is a Melt Flow Index Tester?


A melt flow index tester measures how much molten thermoplastic material passes through a standardized die under a specified temperature and load.


For an MFR test, the extruded material is collected for a defined time and its mass is used to calculate the melt mass-flow rate, normally expressed in g/10 min. MVR measures the volume of material extruded over time and is normally expressed in cm³/10 min.


The result is commonly used to characterize the flow behavior of thermoplastics and compare different material grades. It is particularly useful in polymer quality control because changes in melt flow can indicate differences in material composition, processing history, or degradation.


However, MFR or MVR should not be treated as a complete measurement of polymer performance. ASTM D1238 describes melt flow rate as an empirically defined parameter affected by material structure and test conditions, so results should be interpreted together with the applicable material specification and other relevant tests.


How Does Melt Flow Index Testing Work?


A typical melt flow index test follows a straightforward sequence:

1. The thermoplastic sample is placed into the heated barrel.

2. The material is allowed to reach the specified test temperature.

3. A specified load is applied to the piston.

4. The molten polymer is forced through a standardized die.

5. The extruded material is measured by mass or piston displacement.

6. The MFR or MVR result is calculated and recorded.


The test is controlled primarily by temperature, load, die geometry, timing, and sample preparation. These variables must remain consistent when test results are compared.

UnitedTest melt flow index testers use a standard die with an inner diameter of approximately 2.095 mm and a die length of approximately 8.000 mm. The equipment is designed for controlled testing of thermoplastic materials such as PP, PE, PVC, POM and ABS.


Manual vs Automatic Melt Flow Index Testers


The choice between a manual and automatic melt flow index tester depends mainly on testing frequency, required workflow, and the level of operator involvement.


A basic manual system may require the operator to perform more of the sample cutting, weight handling, timing, and result recording. This approach can be suitable for laboratories with relatively low testing volumes or applications where operators need direct control over each test step.


An automatic melt flow index tester reduces repetitive operations and can improve testing efficiency when multiple samples are tested during the day. UnitedTest's MFI404, for example, provides automatic weight lifting, touchscreen operation, MFR/MVR testing, and both automatic and manual sample cutting.


The practical question is therefore not simply whether automatic equipment is better. It is whether the additional automation improves the specific testing workflow without reducing the operator's ability to control the test.


MFR and MVR Testing in One Melt Flow Index Tester


For laboratories working with different polymer grades, having both MFR and MVR capability can be an important advantage.


MFR determines the mass of polymer flowing through the die over a specified period and is generally reported in g/10 min.

MVR determines the volume of polymer flowing through the die over a specified period and is generally reported in cm³/10 min.


ISO 1133-1:2022 defines both mass-measurement and displacement-measurement procedures for determining MFR and MVR. It also notes that MVR can be particularly useful when comparing materials with different filler contents.


UnitedTest offers models covering different testing requirements. The MFI404 and MFI403 support both MFR and MVR testing, while the MFI402 is designed primarily for MFR testing. This allows laboratories to select equipment according to their actual testing methods rather than purchasing unnecessary functions.


Why Temperature Control Matters


Temperature stability is one of the most important factors in melt flow testing.


Because polymer viscosity changes significantly with temperature, even a relatively small temperature variation can affect the amount of material flowing through the die. For this reason, the melt flow index tester must provide stable heating and accurate temperature control throughout the test.


UnitedTest melt flow index testers provide a temperature range up to 450°C, with a temperature resolution of 0.1°C. The MFI404 automatic model provides temperature fluctuation control of approximately ±0.2°C, while other models use approximately ±0.5°C, depending on configuration.


The required test temperature should always be selected according to the material specification and applicable test standard rather than simply using the polymer's nominal melting temperature.


Choosing the Test Load


The applied load is another critical testing condition.


Different thermoplastic materials and grades are tested under different temperature and load combinations. A tester therefore needs sufficient load options to accommodate different test conditions.


UnitedTest melt flow index testers use eight levels of standard weights with a total mass of 21.6 kg, providing multiple load configurations for different testing requirements. The available load system covers commonly used test loads including 1.2 kg, 2.16 kg, 3.8 kg, 5 kg, 10 kg, 12.5 kg and 21.6 kg configurations.


For laboratories testing multiple polymer grades, this flexibility is more useful than a machine designed around only one fixed test condition.


Manual and Automatic Sample Cutting


Sample cutting is another area where manual and automatic operation can be combined.


During an MFR test, the extrudate is cut at defined time intervals so that the discharged material can be collected and weighed. Manual cutting gives the operator direct control, while automatic cutting can reduce repetitive work and improve timing consistency.


UnitedTest MFI403 and MFI404 models support both manual and automatic cutting. This is useful for laboratories that need flexibility between routine quality-control testing and more hands-on material evaluation.


For laboratories with frequent testing, automatic cutting can help reduce operator workload. For special materials or troubleshooting work, manual cutting remains useful because the operator can observe the extrudate during the test.


Automatic Weight Loading for Higher Testing Efficiency


For laboratories performing frequent melt flow testing, handling standard weights manually for every test can add unnecessary operating steps.


The UnitedTest MFI404 is equipped with an automatic weight loading system, allowing the selected test load to be applied through the instrument rather than requiring the operator to manually handle the complete weight set for every measurement.

Combined with touchscreen control and automatic/manual cutting, this configuration is particularly suitable for laboratories that test multiple polymer grades and need to change test conditions frequently.


This is where automation provides a practical benefit: it reduces repetitive operations while retaining the standard load-based testing principle.


Melt Flow Index Tester Models for Different Laboratory Needs


UnitedTest provides several configurations rather than using one machine for every application.


MFI404 Automatic Melt Flow Index Tester

The MFI404 is the most automated option in the current range. It features:

  • ◆  Touchscreen operation

  • ◆  Automatic weight lifting

  • ◆  MFR and MVR testing

  • ◆  Manual and automatic sample cutting

  • ◆  Temperature control up to 450°C

  • ◆  Eight standard weight levels with a total mass of 21.6 kg

  • ◆  Data display and printing functions

  • ◆  Optional PC software configuration

It is a suitable choice for laboratories that perform frequent testing and want to reduce repetitive operator operations.


MFI403 Melt Flow Index Tester

The MFI403 provides a more straightforward laboratory configuration while retaining MFR and MVR testing capability.

It uses an LCD display and supports both manual and automatic cutting. It is suitable for laboratories that require flexible melt flow testing without necessarily requiring the full automatic weight-loading configuration of the MFI404.


MFI402 Plastic Melt Flow Index Meter

The MFI402 Plastic Melt Flow Index Meter is designed for laboratories that primarily need MFR testing.

It provides LCD display operation, manual and automatic cutting, a temperature range up to 450°C, and multiple standard load configurations. This makes it a practical option for routine melt flow quality control where MVR testing is not required.


Which Standards Apply to Melt Flow Testing?


Melt flow testing should always be performed according to the standard and material specification applicable to the polymer being evaluated.


The major standards associated with melt flow testing include:

  • ◆  ISO 1133-1:2022 — Determination of melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics, Part 1: Standard method.

  • ◆  ASTM D1238-26 — Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer.

  • ◆  ASTM D3364-26 — Standard Test Method for Flow Rates of Non-Rigid Poly(Vinyl Chloride) with Molecular Structural Implications.

  • ◆  JIS K7210

  • ◆  DIN 53735

  • ◆  BS 2782 Part 7, Method 720A


UnitedTest also lists support for additional national and industry-specific testing requirements depending on the instrument configuration.


It is important to note that ISO 1133 and ASTM D1238 address the same general subject but are not technically identical. The applicable material specification can also introduce specific test conditions or procedural requirements. Therefore, laboratories should select the test procedure based on the standard and material specification required for the application.


Melt Flow Index Testing for Quality Control


Melt flow testing is widely used as a routine quality-control tool for thermoplastic materials.


For resin manufacturers, MFR or MVR can help monitor consistency between production batches. For plastic processors, melt flow testing can be used to compare incoming resin with established specifications or reference materials.


A significant change in melt flow rate may indicate a change in material composition, molecular structure, processing history, or thermal degradation. However, the result should be evaluated together with other material properties because MFR is not a complete representation of polymer performance.


ASTM D1238 specifically identifies melt flow testing as useful for quality control and for assessing the uniformity of polymer flow produced by a process.


Applications of Melt Flow Index Testers


Melt flow index testers can be used for a wide range of thermoplastic materials and laboratory applications, including:

  • ◆  Polyethylene (PE)

  • ◆  Polypropylene (PP)

  • ◆  Polyvinyl chloride (PVC)

  • ◆  ABS

  • ◆  POM

  • ◆  Thermoplastic resin and granule testing

  • ◆  Polymer production quality control

  • ◆  Incoming material inspection

  • ◆  Research and development

  • ◆  Material grade comparison

  • ◆  Plastic processing quality control

For cable materials, pipe materials, molded plastics, and other thermoplastic products, melt flow testing can provide a fast and standardized indicator of material flow behavior.


How to Choose Between Manual and Automatic Melt Flow Testing Equipment


When selecting a melt flow index tester, consider five practical factors:


1. Required test method
Determine whether your application requires MFR only or both MFR and MVR.

2. Applicable standard
Confirm the required ISO, ASTM, JIS, DIN, BS, or industry-specific test method before selecting the equipment configuration.

3. Testing frequency
For occasional laboratory testing, a simpler model may be sufficient. For high-frequency quality control, automatic functions can significantly reduce repetitive work.

4. Required load range
Choose a tester with sufficient standard weights for the materials and test conditions used in your laboratory.

5. Operator workflow
Touchscreen control, automatic weight loading, automatic cutting, printing, and data functions can make routine testing more efficient, while manual functions remain useful for specialized testing and operator observation.


Manual or Automatic: Which Melt Flow Index Tester Is Better?


There is no single answer for every laboratory.


A manual or semi-automatic melt flow tester can be a good choice when testing volume is moderate and operators need direct control over the test process. An automatic melt flow index tester is more appropriate when the laboratory performs frequent tests, changes test conditions regularly, or wants to reduce repetitive weight handling and sample cutting.


For laboratories that need both flexibility and efficiency, a combination of automatic and manual functions is often the most practical solution. UnitedTest's MFI series follows this approach by offering different levels of automation, including MFR/MVR measurement, automatic weight loading on the MFI404, and both manual and automatic sample cutting.


With temperature control up to 450°C, multiple standard load configurations, and testing options aligned with major melt flow standards, the UnitedTest melt flow index tester range can be configured for routine quality control, material comparison, and polymer research applications.


Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.