Home >> Application >> By Standard >> ISO >> ISO 10000~19999 >> ISO 10354 Wedge Rupture Test for structural adhesive bonds

ISO 10354 Wedge Rupture Test for structural adhesive bonds

Share:

ISO 10354 Wedge Rupture Tester for Structural Adhesive Bond Durability | UnitedTest

UnitedTest manufactures ISO 10354 wedge rupture testing machines for qualitative durability characterization of structural adhesive bonded assemblies, suitable for adhesive qualification and environmental aging resistance assessment.


ISO 10354 specifies the wedge rupture test method for characterizing the long-term durability of structural adhesive bonded assemblies. This qualitative test assesses the resistance of adhesive joints to crack propagation under combined mechanical and environmental loading, widely used for structural adhesive formulation screening and surface treatment validation. UnitedTest supplies calibrated ISO 10354 wedge rupture test systems for aerospace, automotive and construction adhesive laboratories.


Test Principle

A wedge is progressively inserted into the gap between two adhesively‑bonded substrate plates to generate an initial crack inside the bonded joint. The initial crack length is recorded. Specimens then undergo laboratory ageing treatment. After ageing, the final crack length is measured to calculate crack propagation caused by ageing environment. The failure mode of the joint is also analysed. This test simulates loads and interfacial effects at metal‑adhesive/primer interfaces of bonded assemblies.


Test Specimen Information

Bonded plate (Figure 2): two plates, each 130 mm × 150 mm × (3 ± 0.1) mm, bonded over part of their length (bonded zone 115 mm, with a 35 mm unbonded/debonded starter region at one end).

Key specimen-preparation stipulations:

  • Before bonding, apply a strip of anti-adhesive tape < 0.1 mm thick (typically PTFE) beyond the end of the bonded zone, to create the unbonded starter mouth for wedge insertion — no bonding outside the required zone.

  • Cut four strips 27 mm wide × 150 mm long starting from the centreline; machine the sawn edges to 25 mm ± 0.1 mm final width.

  • Alternative: prepare individual specimens 150 mm × 27 mm × (3 ± 0.1) mm and machine to 25 mm ± 0.1 mm after bonding.

  • Adhesive layer thickness: 3 measurements per specimen at 0.01 mm resolution → record the mean.

  • Number of specimens: at least 10.


Test Equipment for ISO 10354 Wedge Rupture Test for structural adhesive bonds

Recommend UnitedTest Universal testing machine to execute the penetrate the wedge in certain load can constant speed, consist of below:  
Driving speedGiving slow, regular penetration at 30 mm/min ± 5 mm/min, while excluding oblique (skewed) penetration or lateral movement of the wedge.
Wedges

Must be chemically inert to test adherends to avoid electrolytic corrosion; stainless‑steel wedge is recommended.

Key dimensions: 30 mm length, 25 mm width, 3 mm thickness, 60° wedge angle.

Binocular magnifying glassMagnification ×10 to ×40, for locating the crack tip.


Key Test Parameters

Adherend plate size130 mm × 150 mm × (3 ± 0.1) mm
Specimen size (final)150 mm × 25 mm ± 0.1 mm (× 3 ± 0.1 mm thick per half)
Specimen count≥ 10
Anti-adhesive tape< 0.1 mm, PTFE
Wedge penetration speed30 mm/min ± 5 mm/min, non-oblique, regular
Wedge positioningEnd and sides approximately flush with the specimen sides
Crack-tip detectionBinocular magnifier, ×10 – ×40
AgeingOne of the conditions specified in ISO 9142 (e.g. humid/warm exposure)
Post-ageing stabilisation60 min ± 10 min at ambient conditions
Measured quantitiesInitial crack length l₀, final crack length l_F (mean of both edges)
ResultΔl = l_F − l₀ (mm); arithmetic mean of Δl per failure type
Failure-pattern classificationISO 10365
Bondline thickness recordMean of 3 readings, 0.01 mm resolution
PrecisionNot established — no inter-laboratory data available (Clause 7)


General Test Procedures ISO 10354 Wedge Rupture Test for structural adhesive bonds

  1. Prepare specimens  (plates → PTFE tape → surface prep → bond → condition at 23 ± 2 °C → saw 4 × 27 mm strips → machine to 25 ± 0.1 mm → measure bondline thickness ×3).

  2. Open the taped (unbonded) end of the specimen and insert the wedge.

  3. Drive the wedge fully home using the driving device at 30 ± 5 mm/min, keeping it flush with the specimen sides.

  4. Locate the crack tip on each side of the specimen with the ×10–×40 binocular magnifier and mark it with a fine indelible line.

  5. Measure the initial crack length from the wedge/adherend contact point to the mark, on each edge → record the mean initial crack length l₀.

  6. Age the specimen under the selected ISO 9142 condition.

  7. After ageing, let it stand 60 min ± 10 min at ambient conditions to stabilise.

  8. Measure the final crack length on each edge → mean final crack length l_F.

  9. Separate (open) the two halves and determine the failure pattern in accordance with ISO 10365.

  10. Expression of results and test report

    Δl = l_F − l₀ per specimen, plus the arithmetic mean of Δl for each failure type.

       The test report must contain items (a)–(m): reference to ISO 10354; full adhesive/primer identification (nature, origin, manufacturer ref., batch/mix no., form); adherend identification; surface preparation details; bonding procedure (application method, drying/pretreatment, bonding time, temperature, pressure); mean adhesive-layer thickness per specimen; ageing conditions; failure pattern per specimen; l₀ and l_F per specimen; arithmetic mean of l₀ per failure type; Δl per specimen; arithmetic mean of Δl per failure type; and any deviations (especially other plate thicknesses).

ISO 10354 Wedge Rupture Test for structural adhesive bonds


Related & Similar Standards

ISO 10354

Adhesives, Characterization of durability of structural-adhesive-bonded assemblies — Wedge rupture test

ASTM D3762

Standard Test Method for Adhesive-Bonded Surface Durability of Aluminum (Wedge Test)

ISO 8060

Composites and reinforcements fibres — Carbon fibre reinforced plastics (CFRPs) and metal assemblies — Characterization of durability of adhesive interfaces by wedge rupture test

EN 14444

Structural adhesives - Qualitative assessment of durability of bonded assemblies - Wedge rupture test (ISO 10354:1992 modified)

ISO 14165

Adhesives — Durability of structural adhesive joints — Exposure to humidity and temperature under load: a different durability route — constant applied load 

(spring-loaded lap-shear/T-joints, ≈1–7 MPa) in a cyclic 42–48 °C / 95–100 % RH cabinet, measuring time to failure rather than crack growth.

ASTM D3433

Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints

ASTM D1002

Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens


Industry Application

  • Primary applicable substrates: aluminium alloys and titanium alloys for structural adhesive bonding, widely used in aerospace industry.

  • Extended usage: Can assess surface preparation quality for other metals and plastics, provided adherend thickness and rigidity are properly considered.

  • Main purpose: Evaluate environmental durability of structural adhesive joints; also serve as quality‑check method for substrate surface pretreatment before bonding.

Keywords: ISO 10354 wedge rupture tester, structural adhesive bond durability test machine, adhesive joint wedge rupture test equipment, structural adhesive durability characterization tester, bonded assembly environmental resistance test rig, adhesive crack propagation test instrument, structural adhesive qualification tester, adhesive surface treatment verification test, ISO10354 lab test machine, UnitedTest ISO 10354 tester, structural bonding durability analyser

Related products and device

ISO 10354 Single column tensile tester

Carbon black dispersion tester is designed according ISO 18533 standard, used to measure the carbon black dispersion in polyolefin pipes, fittings and compounds. Adaptive to measuring software, and the microscope, measure the size, form, dispersion condition of the carbon black granule.

Electricity hot blast drying oven

Electricity hot blast drying oven is mainly used to measure the dimension change of plastic material after heating, suitable for plastic pipe, plastic sheet etc.

Related Standard

ASTM D3762 Wedge Test – Adhesive-Bonded Surface Durability of Aluminum –

ASTM D3762 Standard Test Method for Adhesive-Bonded Surface Durability of Aluminum (Wedge Test)

ASTM D3762 durability at metal‑adhesive/primer interfaces, and delivers better correlation to real‑world service performance than traditional lap‑shear or peel tests. Though originally designed for aluminum‑to‑aluminum bonding, it can be adapted for other metals and plastics if adherend thickness and rigidity are properly considered. it simulates, qualitatively, the forces and effects acting on a bonded joint at the metal–adhesive/primer interface, and has proven highly reliable for predicting the environmental durability of adherend surface preparations — correlating with service performance far better than conventional lap-shear or peel tests. It is used to control surface-preparation 


ASTM D3433 Cleavage Fracture Test for Adhesive Bonded Metal Joints –

ASTM D3433 Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints

ASTM D3433 determines the fracture strength in cleavage (Mode I opening) of adhesives when tested on standard specimens under specified preparation and testing conditions, delivering the critical strain‑energy‑release‑rate values GIc (initiation toughness) and GIa (crack‑arrest toughness). It focuses on linear elastic fracture mechanics (LEFM) characterization of crack propagation resistance in metal-adhesive joints, with optional adaptation for plastic adherends when rigidity/thickness corrections are applied. 

ASTM D1002 Lap Shear Test of Adhesively Bonded Metal Specimens –

ASTM D1002 is the most widely used standard test for measuring the apparent shear strength of metal‑to‑metal adhesive single‑lap joints under tension loading. It provides comparative data for adhesive selection, process control, and quality assurance in structural bonding applications. It is the most common test for evaluating adhesive shear performance.

ISO 10354 — Wedge Rupture Test: Frequently Asked Questions

Q1. What is the ISO 10354 test?

A qualitative laboratory method that drives a wedge into the bondline of two bonded plates to create a crack at the metal–adhesive/primer interface. The crack length is measured before and after laboratory ageing; the growth of the crack is the measure of the joint's environmental durability.


Q2. Why must the wedge be chemically compatible with the adherends?

To avoid electrolytic (galvanic) corrosion at the wedge/adherend contact, which would introduce corrosion products and falsely accelerate or mask interface degradation.


Q3. Is this a quantitative strength test?

No. ISO 10354 is explicitly qualitative but highly discriminating. It ranks surface preparations, primers and adhesive systems against each other. If you need a quantitative fracture-strength value, use ASTM D3433 (fracture strength in cleavage of adhesives in bonded joints).


Q4. Why is PTFE (anti-adhesive) tape used?

A strip of tape < 0.1 mm thick (polytetrafluoroethylene is generally used) is applied beyond the end of the bonded zone before bonding. It creates an unbonded "mouth" so the wedge can be inserted, and prevents bonding outside the required zone.


Q5. Who uses this test?

Adhesive manufacturers, aerospace and defence OEMs and MROs, automotive and rail Tier-1 suppliers, marine and composites manufacturers, national test laboratories, and QA/process-control departments running bonding lines.


Q6. Which materials does ISO 10354 cover?

Primarily the bonding of aluminium and titanium alloys. It may also be used to assess the surface preparation of other metals and plastics, provided consideration is given to the thickness and rigidity of the adherends.


Q7. What industry fields apply it?

Aerospace and defence (primary), aircraft bonded repair, automotive lightweight body structures, rail rolling stock, marine craft, wind energy blades, electronics and general structural bonded-assembly manufacturing.


Q8. What is it actually used for in practice?

  1. Screening and qualifying surface pretreatments (FPL etch, chromic/phosphoric acid anodising, grit-blast + silane, sol-gel).

  2. Qualifying primers and adhesive systems for environmental durability.

  3. Process control of production surface-preparation operations.

  4. Approving bonded repairs on ageing aircraft and structures.


Q9. At what speed is the wedge driven in?

30 mm/min ± 5 mm/min, slowly and regularly, with the wedge end and sides approximately flush with the specimen sides.


Q10. What is the difference between ISO 10354 and ASTM D3762?

They are equivalent in principle — both are the wedge cleavage/rupture test, ASTM D3762 being known as the Boeing wedge test. ASTM D3762 is written specifically for aluminium-to-aluminium bonds, uses specimens of about 25.4 mm × 203 mm with ~3.2 mm adherends (typically 2024-T3 or 7075-T6), and gives explicit exposure environments and crack-growth reporting. ISO 10354 covers aluminium and titanium and drives its ageing regime from ISO 9142.


Q11. How does ISO 10354 differ from ISO 14615?

Different durability mechanism. ISO 10354 = fixed displacement (wedge), result is crack growth over time. ISO 14615 = fixed load (spring-loaded lap-shear or T-joints at roughly 1–7 MPa) in a cyclically humid/hot cabinet (42–48 °C, 95–100 % RH), result is time to failure.


Q12. How does ISO 10354 differ from ASTM D3433?

ASTM D3433 measures fracture strength in cleavage — a quantitative fracture-mechanics value. ISO 10354 measures durability qualitatively. They are complementary: D3762/ISO 10354 to screen surface treatments, D3433 to quantify fracture toughness.


Q13. What is EN 14444?

EN 14444:2005 — Structural adhesives — Qualitative assessment of durability of bonded assemblies — Wedge rupture test, which is ISO 10354:1992 modified. It restricts the scope to thermosetting structural adhesives and primers on aluminium and titanium alloys and warns that only like should be compared with like (similar adherends bonded with similar adhesives).


Q14. Why is the ISO 10354 wedge rupture test important for materials?

Because structural adhesive joints almost never fail through the bulk adhesive — they fail because water reaches the metal–adhesive (or primer) interface and displaces or hydrates the oxide. The wedge test puts a crack tip exactly at that interface and holds it open, so the two agents that destroy real joints — sustained stress and moisture at the crack tip — act together.


Q15. Why is it better than lap-shear or peel testing for durability?

Conventional lap-shear and peel tests cannot simultaneously simulate sustained stress and environment, and moisture must diffuse in slowly from the joint edges. In the wedge test the crack tip sits in a high-tensile-stress region that is directly exposed to the environment, so degradation is far more representative. ASTM states the method correlates with service performance much more reliably than conventional lap-shear or peel tests, which is why organisations such as NASA and Boeing adopted it.


Q16. What does a compliant ISO 10354 testing machine need to deliver?

A controlled, non-oblique wedge drive at 30 mm/min ± 5 mm/min, a wedge of non-corroding (typically stainless steel) construction, rigid specimen fixturing to keep the wedge flush with the specimen sides, provision for crack-tip observation at ×10–×40, and interface/accessories for bondline thickness measurement to 0.01 mm and for timing the 60 min ± 10 min post-ageing stabilisation.


Q17. Why choose ISO 10354 Wedge Rupture Test Machine from UnitedTest?

UnitedTest is professional manufacturer for ISO 10354 wedge rupture test equipment. Our complete wedge rupture test system evaluates environmental durability of structural adhesive‑bonded assemblies for aerospace aluminium, titanium alloys and other substrates. Supply standard wedge fixture, controlled‑speed driving device, binocular magnifier set, full compliance with ISO 10354 standard. Suitable for adhesive lab, aerospace quality control, material R&D.


UnitedTest, reliable manufacturer of material mechanical testing equipment, provides complete ISO 10354 wedge rupture test solutions for structural adhesive bonded joint durability characterization.

The ISO 10354 wedge rupture test (also called wedge cleavage test) is widely adopted in aerospace industry to assess metal‑adhesive‑primer interface performance and verify substrate surface‑preparation quality for aluminium alloy, titanium alloy and other metal adherendsISO.

Our ISO 10354 wedge rupture test system includes:

  • Standard stainless‑steel test wedge following ISO 10354 drawing dimensions

  • Precision wedge‑driving unit, adjustable speed strictly covering 30 mm/min ±5 mm/min requirement, prevents oblique wedge movement

  • Matching binocular magnifying assembly (×10‑×40) for crack‑tip observation and marking

  • Thickness measuring accessory, stop‑watch accessory

  • Compatible with our universal testing machine platform for laboratory adhesive durability evaluation.

This test equipment supports the full ISO 10354 workflow: specimen wedge insertion, initial crack measurement, post‑ageing final crack reading, failure‑pattern analysis. It helps engineers compare different structural adhesives, primers and surface‑treatment processes by measuring crack‑growth Δl after environmental ageing according to ISO 9142 conditions.


Typical application fields: aerospace adhesive bonding R&D, quality inspection of structural adhesives, surface pretreatment validation for metal bonding, adhesive material laboratory testing.

UnitedTest delivers turn‑key testing solutions: machine hardware, standard fixtures, operation guidance referencing ISO 10354, ISO 4588, ISO 9142 and ISO 10365 standards. Contact us for ISO 10354 wedge rupture test machine quotation and technical support.

< Previous: ISO 10333-1 Full-body harnesses personal fall-arrest testing

> Next: ISO 10364 Determination the Pot Life of Multi-Component Structural Adhesives

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.