Home >> Application >> By Standard >> ISO >> ISO 5000~9999 >> ISO 6312 Brake Lining Shear Strength Testing

ISO 6312 Brake Lining Shear Strength Testing

Share:

ISO 6312 Brake Lining Shear Tester for Disc Pads & Drum Brake Shoes | UnitedTest

UnitedTest manufactures ISO 6312 shear test machine for disc brake pad and drum brake shoe assemblies. This equipment tests the bond shear strength between friction lining and metal backing plate for bonded, integrally moulded and MRS brake assemblies, excluding riveted linings.


ISO 6312 Road vehicles — Brake linings — Shear test procedure for disc brake pad and drum brake shoe assemblies. ISO 6312 defines standardized laboratory shear testing for disc brake pad and drum brake shoe assemblies to evaluate bond shear strength between friction brake lining and its metal carrier or backing plate. It covers integrally moulded, bonded and mechanical-retention-system (MRS) brake assemblies, while riveted lining assemblies fall outside this standard’s scope. Widely adopted for automotive friction material quality control, production validation and regulatory compliance testing for road vehicle brake components.


Test Principle

The assembly is gripped so that the friction material is held while a loading tool (ram/punch) pushes against the edge of the lining, parallel to the bond line, until the lining shears off the carrier.

τ = F/A 

  • F = shear force at failure (N) — the total load at the instant of shear failure

  • A = bond area (mm²) — the contact area between lining and carrier, taken at the bond line (from the friction‑material profile at the bond line, not at the pad face, because chamfers and slots are pad‑surface effects)

  • τ = shear strength at failure (MPa)

Key idea: a pure shear stress state is produced at the lining/carrier interface, and the peak load divided by the bonded area gives the interfacial (or cohesive) strength. The result is reported as the minimum and the average of all samples tested, because the minimum governs safety.


Test Specimen Requirements

  • Specimens can be complete brake assemblies or cut coupon segments. If cut coupons are used, load direction (radial / tangential relative to vehicle mounting position) must be recorded in the test report.

  • Standard test sample quantity: five specimens.

  • For drum‑brake shoes, segments can be sawn down to the carrier base for segmented testing.


Test Equipment of ISO 6312 Brake Lining Shear Strength Testing

Universal Testing Machine
  • A compression or tensile (universal) testing machine or dedicated shear‑testing machine of sufficient capacity, applying the shearing load via an activated ram.

  • Must be able to record the exact load at the instant of shear failure (peak‑load capture / load registration).

  • Controlled loading: average load rate (4 500 ± 1 000) N/s; if a constant crosshead‑speed machine is used, set (10 ± 1) mm/min.

  • The type of machine control (load rate or crosshead speed) must be reported, so results from different rigs can be compared.

  • Shock loading must be avoided.

Fixtures (General)
  • Must hold the sample parallel to the loading tool.

  • Tool radius in contact with the sample: ≤ 2 mm (to avoid sharp edges); if a specific radius is used, note it as a deviation.

    If the loading‑tool contact area includes the draft angle of the friction material, note it on the report.

Drum brake shoe fixture 1
  • Loading tool contacts the lining edge over the full sample length and thickness, within (1 ± 0,2) mm of the shoe platform.

  • Load applied parallel to the plane of the shoe platform; centre of thrust of the ram positioned accordingly.

  • The shoe is supported to give uniform loading along the lining length; the shoe platform support thickness ≤ platform thickness.

  • Width of the loading tool > width W of the lining; a lining face support and fixed bottom tool complete the fixture.

ISO 6312 Brake Lining Shear Strength Testing

Disc brake pad fixture 2
  • Plane of the backplate parallel to the plane of the loading tool.

  • Loading tool contacts the lining edge within (1 ± 0,2) mm of the backing plate, conforms to the lining profile (including optional moulding draft angles), and is self‑aligning (pivot).

  • Contact over the full sample length of the lining edge parallel to the backplate support.

  • Load‑bearing edge of the backing plate rests against a rigid support no thicker than the backing plate (C ≤ backplate thickness).

  • A pressure fixture applies a face load of (0,5 ± 0,15) N/mm² of lining area, perpendicular to the shear load, to prevent assembly movement — applied so that friction is minimised and does not significantly influence the shear measurement.

ISO 6312 Brake Lining Shear Strength Testing


Key Test Parameters & Mandatory Stipulations

Elevated‑temperature optionHeat uniformly to bond‑line temperature within 30 min, test 60 s after removal from the heating unit; recommended (200 ± 10) °C for drum brake linings, (300 ± 10) °C for disc pads
Load rate (load‑controlled)(4 500 ± 1 000) N/s average
Crosshead speed (displacement‑controlled)(10 ± 1) mm/min
Loading‑tool radius≤ 2 mm
Tool clearance from carrier / shoe platform(1 ± 0,2) mm
Disc‑pad face (clamping) load(0,5 ± 0,15) N/mm² of lining area
Number of samples5 recommended
UnitsF in N, A in mm², τ in MPa
ReportingMinimum and average shear force and/or shear strength


Detailed Test Procedure of ISO 6312 Brake Lining Shear Strength Testing

  1. Prepare and condition specimens as per sampling requirements; select correct fixture according to brake‑assembly type.

  2. Perform test either at ambient temperature or elevated temperature following heating rules above.

  3. Mount specimen into fixture with documented loading orientation (radial or tangential). Apply required face pre‑load for disc‑pad samples.

  4. Apply shear load at specified rate continuously until full shear failure takes place; capture failure load value.

  5. (Optional) Evaluate fracture failure pattern: record percentage distribution of three failure modes: clean carrier exposure, fracture inside adhesive layer, fracture inside lining / underlayer.

    • Optional chemical verification: use reference solution (copper‑sulphate‑based mixed solution) to distinguish adhesive‑interface failure versus cohesive fracture inside friction material.

  6. Compute shear strength τ = F / A. Report both minimum value and arithmetic average among tested samples.

  7. Compile full test report according to Annex‑B format of ISO 6312. Annex‑A provides a normative flowchart for the whole workflow.


Test Applications (Industry Fields)

  • Friction‑material manufacturers — formulation development, moulding/bonding process validation, batch release.

  • Automotive OEMs and Tier‑1 brake suppliers — supplier qualification, incoming inspection, PPAP/series monitoring.

  • Independent test laboratories and certification bodies — compliance testing to OEM specs and national adoptions.

  • Quality assurance over the product life cycle — from prototyping through series production, and for assessing durability after conditioning (fluid exposure per ISO 6314, corrosion, heat) or after service/dynamometer testing — i.e. how much bond strength is retained.

  • Comparing attachment technologies — bonded vs. integrally moulded vs. MRS backplate designs.

  • It is one of the standard physical‑property test items listed in the ISO 15484 quality‑assurance test plan for brake lining friction materials


Related Standards: 

ISO 6313

Road vehicles; Brake linings; Effects of heat on dimensions and form of disc brake pads; Test procedure

GB/T 22310

Road vehicles—Brake linings—Effects of heat on dimensions and form of disc brake pads test method

SAE J160Swell, Growth, and Dimensional Stability of Friction Materials and Noise Insulators when Exposed to Elevated Temperatures — referenced by ISO 6313
SAE J2581Thermal Transport Properties Germane to Friction Materials and Brakes — referenced by ISO 6313
SAE J840North‑American recommended practice for brake‑lining shear testing, technically comparable with ISO 6312 for automotive brake assemblies
ISO 6310

Compressive strain and thermal swell test for brake pads;

measures combined compressibility and thermal dimensional growth under load-temperature cycles, overlapping thermal stability evaluation scope with ISO 6313 but with different rig geometry and test loading logic.

ISO 6312Shear strength of full disc brake pad assemblies (bonds friction material to backing plate; post-ISO 6313 thermal test destructive validation).
ISO 6311Internal shear strength of the lining material itself (not the lining‑to‑carrier bond) — the closest "sibling" test.
ISO 6314Evaluates brake-lining resistance against water, salt solution, oil and brake-fluid contamination
ISO 15484Brake lining product quality assurance standard; lists ISO 6313 as a mandatory thermal stability test for friction material qualification reports
JIS D 4422(Japan) — Automotive parts — Drum brake shoe assemblies and disc brake pad — Shear test procedure.
GB/T 22309China standard, equal to ISO 6312
JIS D4413Automotive parts -- Brake linings and brake pads -- Compressive strain test method


Keywords: ISO 6312 brake lining shear tester,disc brake pad shear strength test machine,drum brake shoe shear tester,brake lining bond strength tester,automotive brake friction material test rig,brake pad backing plate shear test,MRS brake assembly shear test,brake lining adhesion tester,UnitedTest brake testing machine,road vehicle brake lining test equipment,brake pad shear test instrument,brake shoe assembly mechanical test,brake friction material quality testing,ISO 6312 test fixture,automotive brake component tester

Related products and device

ISO 6312 Brake Lining Shear Strength Testing universal testing machine

UnitedTest universal testing machine with various test fixture, like peel, flexure, puncture, tear, pneumatic grip, belt tension etc., can be used to almost all materials include but not limited to steel rod, rubber, steel wire, plastic, seat belt, textile, wood, panel etc., mechanical performance inspection.

ISO 6310 Brake liningCompressive Strain testing machine

Professional Brake Lining Compress Strain & Thermal Expansion Testing Machine by UnitedTest. Compliant with ISO 6310 & ISO 6313. Measure compressive strain, thermal swell and heat conduction of disc/drum brake pads and friction materials.

Related Standard

ISO 6313 Disc Brake Pad Thermal Heat Resistance Test –

ISO 6313 Road vehicles - Brake linings - Effects of heat on dimensions and form of disc brake pads - Test procedure

ISO 6313 specifies a combined test method that simultaneously measures: 1, dimensional changes of a disc brake pad as a function of temperature, 2, the pad's resistance to heat transfer in the direction of the applied pressure. 


ISO 6310 Compressive Strain Test for Brake Linings –

ISO 6310 Road vehicles - Brake linings - Compressive strain test methods

ISO 6310 defines unified lab testing procedures to measure compressibility, compressive strain, thermal swell, permanent thermal growth, and heat transfer performance of brake linings under mechanical compression at ambient and high temperatures (400 °C). Two distinct test methods (Method A & B) are specified for different sample types: raw friction material coupons, air brake pads, commercial vehicle linings, and complete hydraulic passenger car disc brake pad assemblies. Unlike ISO 6313 which focuses on passive heat-induced dimensional deformation without heavy mechanical load, ISO 6310 evaluates thickness deformation under simulated brake caliper compression force combined with thermal exposure, replicating real braking load-heat combined working conditions. 

FAQs for ISO 6312 Brake Lining Shear Test

ISO 6312 Brake Lining Shear Testing Machine — Disc Brake Pad & Drum Brake Shoe Bond Strength Tester


Q1. What is the ISO 6312 test?

A. ISO 6312 (Road vehicles — Brake linings — Shear test procedure for disc brake pad and drum brake shoe assemblies) is the international standard method for measuring the shear strength of the bond between the friction material (lining) and its carrier — the steel backing plate on a disc pad, or the shoe platform on a drum brake shoe. The current version is ISO 6312:2010 (3rd edition), confirmed again in 2023.


Q2. Which products can be tested, and which are excluded?

A. It applies to integrally moulded, adhesively bonded, and mechanical retention system (MRS) disc pad and drum shoe assemblies for road vehicles — as complete parts or as cut sections/coupons. It does not apply to riveted assemblies, because in those the mechanical fastener, not the bond, carries the load.


Q3. What is actually measured — and in what units?

A. The shear force at failure F (N) is recorded, divided by the bond area A (mm²) measured at the bond line, giving shear strength τ in MPa: τ = F/A. Results are reported as the minimum and the average of all samples tested.


Q4. Why is this test important?

A. Because debonding is a catastrophic, non-gradual failure. If the friction block separates from the backing plate under braking load, braking force is lost instantly. Shear strength is the single most direct measure of resistance to that event.


Q5. Isn't measuring the friction material's own strength (ISO 6311) enough?

A. No. ISO 6311 measures the internal shear strength of the lining material; ISO 6312 measures the interface — the weakest link in an assembly. A lining can be very strong internally yet fail because of poor adhesive, wrong cure, contaminated backplate or bad moulding parameters. Only ISO 6312 isolates that.


Q6. Why is the minimum value reported, not just the average?

A. Because a brake assembly is only as reliable as its weakest sample. A high average can hide one defective part caused by a local bonding fault, and in a safety-critical component the minimum governs the acceptance decision.


Q7. Why is the failure mode analysed and not just the number?

A. The number tells you how much load was needed; the failure pattern tells you why:

  • Failure inside the lining or underlayer (cohesive) → bond is stronger than the material = healthy margin;

  • Failure in the adhesive layer or exposing clean carrier (adhesive) → surface prep, adhesive, cure or contamination problem.
    The optional CuSO₄ reference-solution test makes this distinction objective rather than visual guesswork.


Q8. Why test at high temperature?

A. Resin softening, oxidation and thermal-expansion mismatch at the interface appear only when hot. ISO 6312 therefore offers 200 °C for drum linings and 300 °C for disc pads — the conditions under which real debonding happens during severe or fade braking. Comparing ambient vs. hot results shows the thermal margin.


Q9. What makes the fixture critical?

A. Small geometric errors change the result significantly. The standard requires: sample held parallel to the tool; tool contact radius ≤ 2 mm; tool edge within (1 ± 0,2) mm of the carrier/backing plate; full-length contact; self-aligning tool for disc pads; rigid backplate support no thicker than the backplate; and a face load of (0,5 ± 0,15) N/mm² applied perpendicular to the shear load while keeping friction negligible.


Q10: What are the two valid loading‑control modes specified in ISO 6312:2010?

A: 1. Load‑rate control: average loading rate 4500 ± 1000 N/s

2. Constant cross‑head speed mode alternative: 10 ± 1 mm/min

You must record which control mode you use in the final report, as results from different machine control modes cannot be directly compared without this note. Shock loading is strictly forbidden during the whole test process.


Q11: My lab gets inconsistent ISO 6312 shear‑test results. What are common root causes?

  1. Incorrect bond‑area calculation (using friction‑surface area instead of carrier‑lining interface area).

  2. Missing or mis‑adjusted disc‑pad face pre‑load, sample slippage occurs.

  3. Sharp loading‑tool edge (radius > 2 mm) cuts friction material instead of triggering true interface shear failure.

  4. Shock impact loading, not following 4500 N/s or 10 mm/min loading rules.

  5. Hot‑test non‑compliance: wrong heating duration, waiting time deviates from 60 seconds after oven removal.

  6. Coupon‑sample tested without recording radial/tangential load orientation.


Q12: Why choose ISO 6312 Brake Lining Shear Strength Testing Machine from UnitedTest?

A: UnitedTest manufactures ISO 6312 disc brake pad & drum brake shoe shear strength testing machines. Custom fixtures for ambient & high‑temperature brake bond‑strength quality‑control & R&D.

UnitedTest is a professional manufacturer of automotive material testing equipment, supplying complete ISO 6312:2010‑compliant brake lining shear‑test solutions for brake‑pad factories, automotive component laboratories, third‑party test houses and university R&D centers worldwideUnitedTest.


Our ISO 6312 shear test machine verifies bond‑interface shear strength between friction lining and metal carrier for disc‑brake‑pad and drum‑brake‑shoe assemblies. It performs both ambient‑temperature and elevated‑temperature shear tests for bonded, integrally‑moulded and MRS mechanical‑retention brake assemblies, complying fully with ISO 6312:2010 international road‑vehicle brake‑lining standards.


Core features of UnitedTest ISO 6312 brake shear test setup:

✅ Accurate dual‑control modes: load‑rate control at 4500 ± 1000 N/s OR constant cross‑head speed 10 ± 1 mm/min as required by ISO 6312:2010 

✅ Custom‑manufactured dedicated fixtures for disc brake pads and drum brake shoes; loading‑tool edge radius ≤ 2 mm; adjustable disc‑pad face pre‑load of 0.5 ± 0.15 N/mm² 

✅ Support full‑assembly test and coupon‑segment specimen testing; records radial / tangential load orientation 

✅ High‑temperature optional chamber for hot‑shear testing at 200 °C (drum shoe) /300 °C (disc pad) 

✅ Software auto‑calculates shear‑strength τ=F/A, outputs minimum & average values, captures force‑displacement curves, generates ISO 6312‑format test reports with failure‑mode documentation 

✅ Avoid shock‑loading; high‑precision load‑cell captures exact peak failure‑load instantaneously 

✅ Compatible with related standards: ISO 6314, ISO 611, SAE J840 for global automotive homologation requirements


Typical use‑cases:

  • Brake‑lining new‑product R&D validation

  • Production‑line incoming‑quality‑control & batch release inspection

  • Post‑environmental‑treatment shear performance testing (after ISO 6314 fluid / salt ageing)

  • After dynamometer or field service residual bond‑strength evaluation

  • Global market product certification for OEM and aftermarket replacement brake parts

UnitedTest delivers complete turn‑key packages: main test machine, ISO‑6312‑specified fixture sets, software, calibration, operation training and after‑sales technical support. We customize fixtures for special brake‑pad geometry, high‑aspect‑ratio, slotted or chamfered brake‑pad samples.

< Previous: ISO 6310 Compressive Strain Test for Brake Linings

> Next: ISO 6313 Disc Brake Pad Thermal Heat Resistance Test

Require More Customized Solutions?

We offer customization to meet your specific needs. Our expert team will collaborate with you to develop the perfect product for you
Customize Now

Beijing United Test Co., Ltd.